Daikin MicroTech III, Troubleshooting Manual

Page: 7 / 40

Download and Configuration
www.DaikinApplied.com 7 OM 1085-6 • MICROTECH III CONTROLLER
Figure 3: BACnet and LonWorks Communication Module Software Version Labels
Table 5: MicroTech III WSHP – Overview of Board Programming Tools
MicroTech III WSHP Programming Tools by Unit Controller Part Numbers
Unit Controller Hardware: 668105611
I/O Expansion Board Hardware: 668105711
Unit Controller Hardware: 668105601
I/O Expansion Board Hardware: 668105702
Hardware
Renesas E2 Lite or E1 programmer available at
www.renesas.com/us/en/products/software-tools/tools/emulator/
e2-emulator-lite.html
Renesas E8a programmer, available at www.renesas.com/us/
en/products/software-tools/tools/emulator/e8a.html
The original Segger Flasher5 programmer can also be used to
program legacy boards. However, it is no longer available from
the supplier for purchase. Instructions are provided in previous
versions of OM 1085
Additional custom 6-pin interface cable ( Figure 6 ) that connects
the unit controller to the Renesas programmer cable.
This cable
is not included in Renesas E2 Lite or E1 programmer kit when
ordered from Renesas.
Contact the ATS Technical Response
Team at 315-282-6434 to request this cable
Additional custom 10-pin interface cable that connects the unit
controller JTAG port to Renesas E8a programmer.
This cable
is not included in Renesas E8a programmer kit when ordered
from Renesas.
Contact the ATS Technical Response Team at
315-282-6434 to request this cable
Software
Renesas Flash Program (RFP) software available at
www.renesas.com/us/en/software/D3017334.html
Renesas Flash Development Toolkit software available at
www.renesas.com/us/en/products/software-tools/tools/
programmer/flash-development-toolkit-programming-gui.html
Unit controller software, which is a “.hex” file type and needs
to be saved to your hard drive. Contact the ATS Technical
Response Team at 315-282-6434 to request a copy of this file
Unit controller software, which is a “.mot” file type and needs
to be saved to your hard drive. Contact the ATS Technical
Response Team at 315-282-6434 to request a copy of this file
No Program/Run jumper is used Program/Run jumper is used
BACnet Communication Module (Applies to
all
MicroTech III WSHP Unit Controllers)
Hardware
BACnet communication module installed on the WSHP baseboard
1. Segger J-Link programmer, available at
www.segger.com or
2. ATMEL SAM-ICE programmer, available at www.DigiKey.com . Reference AT91SAM-ICE-ND or equivalent
Software
Segger J-Link software and documentation pack for Windows available at www.segger.com/downloads/jlink/#J-
LinkSoftwareAndDocumentationPack
SAM-BA v2.18 software free download available at www.microchip.com/DevelopmentTools/ProductDetails/PartNO/SAM-BA%20
In-system%20Programmer
BACnet .bin file is available by contacting the Controls Customer Support group at 866-462-7829
LonWorks Communication Module (Applies to
all
MicroTech III WSHP Unit Controllers)
Hardware
LonWorks communication module installed on the WSHP baseboard
Twisted pair cable with 3-pin connector: Echelon TP/FT-10 to USB network interface, U10 or similar
Software
XIF/NXE files - www.DaikinApplied.com or www.lonmark.org
LonWorks application such as LonMaker SR4, OpenLNS CT, or CT available from Echelon at www.echelon.com
BACnet module software
version label
LonWorks module software
version label