manualshive.com logo in svg

Daikin Inverter FLKS25BVMB, Installation Manual

Share
Download
Daikin Inverter FLKS25BVMB Installation Manual Download Page 13

11

■

English

Refrigerant piping work

2-2. Selection of Copper and Heat Insulation materials

• When using commercial copper pipes and fittings, observe the following:

1) Insulation material:  Polyethylene foam

Heat transfer rate:  0.041 to 0.052kW/mK (0.035 to 0.045 kcal/mh

°

C)

Refrigerant gas pipe’s surface temperature reaches 110

°

C max.

Choose heat insulation materials that will withstand this temperature.

2) Be sure to insulate both the gas and liquid piping and to provide insulation dimen-

sions as below.

3) Use separate thermal insulation pipes for gas and liquid refrigerant pipes.

Gas side

Liquid side

25/35 class

50/60 class

25/35/50/60 class

O.D. 9.5mm

O.D. 12.7mm

O.D. 6.4mm

Thickness 0.8mm

Thickness 0.8mm

Gas pipe thermal insulation

Liquid pipe thermal insulation

25/35 class

50/60 class

25/35/50/60 class

I.D. 12-15mm

I.D. 14-16mm

I.D. 8-10mm

Thickness 10mm Min.

Gas pipe

Liquid pipe

Gas pipe 
insulation

Liquid pipe 
insulation

Finishing tape

Drain hose

Inter-unit wiring

01_EN_2P098794-2T.fm  Page 11  Wednesday, April 14, 2004  10:50 AM

Summary of Contents for Inverter FLKS25BVMB
















Reviews:

No comments

Brands by name

Popular brands

Load more brands