2
English
• Do not install the air conditioner in the following locations:
1. Where there is a high concentration of mineral oil spray or
vapour (e.g. a kitchen).
Plastic parts will deteriorate, parts may fall off and water
leakage could result.
2. Where corrosive gas, such as sulphurous acid gas, is pro-
duced.
Corroding of copper pipes or soldered parts may result in
refrigerant leakage.
3. Near machinery emitting electromagnetic radiation.
Electromagnetic radiation may disturb the operation of the
control system and result in a malfunction of the unit.
4. Where flammable gas may leak, where there is carbon
fibre or ignitable dust suspensions in the air, or where vol-
atile flammables such as paint thinner or gasoline are
handled.
Operating the unit in such conditions may result in fire.
• The air conditioner is not intended for use in a potentially
explosive atmosphere.
2.
BEFORE INSTALLATION
When moving the unit after removing it from the box,
remove the corner covers and use the 4 hoisting hooks to
move it. Do not apply force to the refrigerant piping, drain
piping or resin parts.
• When moving the unit while removing it from the box, be
sure to lift it by holding on to the four lifting lugs without
exerting any pressure on other parts, especially swing flap,
the refrigerant piping, drain piping, and other resin parts.
• Be sure to check the type of R410A refrigerant to be used
before installing the unit. (Using an incorrect refrigerant will
prevent normal operation of the unit.)
• Decide upon a line of transport.
• Leave the unit inside its packaging while moving, until
reaching the installation site. Use a sling of soft material,
where unpacking is unavoidable or protective plates
together with a rope when lifting, to avoid damage or
scratches to the unit.
• Refer to the installation manual of the outdoor unit for items
not described in this manual.
• A separate BEV unit is required for this model.
See the installation manual that comes with the BEV unit
when doing the installation.
• Installation should only be carried out after checking in
advance the type of refrigerant to be used. (Using the wrong
refrigerant will prevent the unit from functioning properly.)
• Do not dispose of any parts necessary for installation until
the installation is complete.
2-1
PRECAUTIONS
• Be sure to read this manual before installing the indoor unit.
• When selecting installation site, refer to the paper pattern.
• This unit is suitable for installation in a household, commer-
cial and light industrial environment.
• Do not install or operate the unit in rooms mentioned below.
• Laden with mineral oil, or filled with oil vapor or spray like
in kitchens. (Plastic parts may deteriorate.)
• Where corrosive gas like sulfurous gas exists. (Copper
tubing and brazed spots may corrode.)
• Where volatile flammable gas like thinner or gasoline is
used.
• Where machines can generate electromagnetic waves.
(Control system may malfunction.)
• Where the air contains high levels of salt such as that near
the ocean and where voltage fluctuates greatly such as
that in factories. Also in vehicles or vessels.
2-2
ACCESSORIES
Check the following accessories are included with the unit.
2-3
OPTIONAL ACCESSORIES
• The remote controller are required for this indoor unit.
• These are two types of remote controllers: wired and wire-
less. Select a remote controller from Table 1 according to
customer request and install in an appropriate place.
(For installation, follow the Installation manual included with
the remote controllers.)
Table 1
NOTE
• If you wish to use a remote controller that is not listed in
Table 1, select a suitable remote controller after consulting
catalogs and technical materials.
Name
1) Drain hose
2) Metal clamp
3) Washers for
locking hanger
Quantity
1 pc.
1 pc.
8 pcs.
Shape
Name
4) Clamp
5) Washer fixing
plate
Insulation for
fitting
Quantity
6 pcs.
4 pcs.
1 each
Shape
6) For gas piping
7) For liquid piping
Name
Sealing pad
10) Elbow
11) Paper pattern
for installation
Quantity
2 pcs.
1 pc.
1 pc.
Shape
8) Large
9) Small
Also used as
packing material
Name
12) Blocking pad
13) Retainer for
blocking pad
14)Retainer for
blocking pad
Quantity
2 pcs.
2 pcs.
2 pcs.
Shape
Name
15) Center retainer
for blocking pad
(Other)
• Operation manual
• Installation manual
Quantity
2 pcs.
Shape
Remote controller
Wired type
Wireless type
Heat pump type
Cooling only type
01_EN_3P086156-10X.fm Page 2 Wednesday, April 15, 2009 3:48 PM