background image

English

9

9. ELECTRIC WIRING WORK

9-1 GENERAL INSTRUCTIONS

Shut off the power before doing any work.

All field supplied parts and materials, electric works must 
conform to local codes.

Use copper wire only.

See also the “Wiring Diagram plate” attached to the control 
box lid when laying electrical wiring.

For details on hooking up the remote controller, refer to the 
“REMOTE CONTROLLER INSTALLATION MANUAL”.

All wiring must be performed by an authorized electrician.

This system consists of multiple indoor units. Mark each 
indoor unit as unit A, unit B . . . , and be sure the terminal board 
wiring to the outdoor unit and BS unit are properly matched. If 
wiring and piping between the outdoor unit and an indoor unit 
are mismatched, the system may cause a malfunction.

A circuit breaker capable of shutting down power supply to 
the entire system must be installed.

Refer to the installation manual attached to the outdoor unit 
for the size of power supply wiring connected to the outdoor 
unit, the capacity of the circuit breaker and switch, and wiring 
instructions.

Be sure to ground the air conditioner.

Do not the earth wire should come in contact with gas pipes, 
water pipes, lightning rods, or telephone earth wires.

Gas pipes: gas leaks can cause explosions and fire.

Water pipes: they cannot be grounded if hard vinyl pipes

are used.

Telephone earth wire and lightning rods: the ground 
potential when struck by lightning gets extremely high.

To avoid short circuiting the power supply wire, be sure to 
use insulated terminals.

Do not turn on the power supply (circuit breaker or earth leak-
age breaker) until all other work is done.

9-2 SPECIFICATIONS FOR FIELD SUPPLIED FUSES 

AND WIRE

Power-related

NOTES

1. Shows only in case of protected pipes. Use H07RN-F in 

case of no protection.

2. Insulated thickness : 1mm or more.

3. If the wiring is in a place where people it can be easily 

touched by people, install an earth leakage breaker to pre-

vent electric shock.

4. When using an earth leakage breaker, make sure to select 

one useful also to protection against overcurrent and short-

circuit.

When using an earth leakage breaker only for earth device, 

make sure to use a wiring interrupter together.

The length of the transmission wiring and remote controller 

wiring are as follows.

Length of the transmission wiring and remote controller wiring

9-3 ELECTRICAL CHARACTERISTICS

MCA: Minimum Circuit Amps (A)  MFA:Max. Fuse Amps (A)

KW:  Fan motor output (kW)

FLA:Full Load Amps (A)

Model

Power supply wiring (including earth wire)

Number 

of units

Field 

fuses 

Wire

Size

15 · 20 · 25 · 32  type

1

16 A

H05VV-U3G

(NOTE 1)

Size must  
comply with 
local codes.

40 · 50  type
63  type

Model

Transmission wiring

Remote controller wiring

Wire

Size (mm

2

)

15 · 20 · 25 · 32 type

Sheathed vinyl cord 
or cable (2 wires) (NOTE 2)

0.75 - 1.25

40 · 50  type
63  type

Outdoor unit – Indoor unit

Max. 1000m

(Total wiring length: 2000m)

Indoor unit –  Remote controller

Max. 500m

Units

Power supply

Fan motor

Model

Hz Volts

Voltage 
range

MCA

MFA

KW

FLA

15 · 20 · 25 · 32

50

220-

240

Min. 

198

  Max.  

264

0.4

16

0.036

0.3

40 

0.5

0.038

0.4

50

0.5

0.038

0.4

63

0.6

0.060

0.5

15 · 20 · 25 · 32 

60

220

Min. 

198

  Max.  

242

0.4

16

0.036

0.3

40

0.5

0.038

0.4

50

0.5

0.038

0.4

63

0.6

0.060

0.5

Summary of Contents for FXDQ15A2VEB





















Reviews: