background image

English

7

Table 4

7.

DRAIN PIPING WORK



Rig the drain pipe as shown below and take measures 

against condensation. Improperly rigged piping could lead 
to leaks and eventually wet furniture and belongings.



(1) Carry out the drain piping

• The diameter of the drain pipe should be greater than or 

equal to the diameter of the connecting pipe (vinyl tube; 
pipe size: 25 mm; outer dimension: 32 mm).

• Keep the drain pipe short and sloping downwards at a 

gradient of at least 1/100 to prevent air pockets from 
forming.

• If the drain hose cannot be sufficiently set on a slope, exe-

cute the drain raising piping.

• To keep the drain hose from sagging, space hanging 

wires every 1 to 1.5 m.

CAUTION

Setting the unit at an angle opposite to the drain piping 
might cause leaks.

• Use the drain hose and the metal clamp. 

Insert the drain hose into the drain socket, up to the tape. 
Tighten the clamp until the screw head is less than 4 mm 
from the hose.

• Wrap the attached sealing pad over the clamp and drain 

hose to insulate.

• Insulate the drain hose inside the building.

 PRECAUTIONS FOR DRAIN RAISING PIPING 

• Install the drain raising pipes at a height of less than 

310 mm.

• Install the drain raising pipes at a right angle to the indoor 

unit and no more than 300 mm from the unit.

If converging multiple drain pipes, install according to the 
procedure shown below.

Select converging drain pipes whose gauge is suitable for 
the operating capacity of the unit.

(2) After piping work is finished, check drainage flows 

smoothly.

• Open the water inlet lid, add approximately 2.5 liter of 

water gradually and check drainage flow.

[ WHEN ELECTRIC WIRING WORK IS FINISHED ]

• Check drainage flow during COOL running, explained under 

“TEST OPERATION.”

Pipe size

Further tightening angle

Recommended arm length 

of tool

 6.4 (1/4”)

60 to 90 degrees

Approx. 150mm

 9.5 (3/8”)

60 to 90 degrees

Approx. 200mm

 12.7 (1/2”)

30 to 60 degrees

Approx. 250mm

 15.9 (5/8”)

30 to 60 degrees

Approx. 300mm

1-1.5m

1-1.5m

Hanger bracket

Metal clamp 

Drain hose

Tape

4mm

Large sealing pad

Metal clamp

(accessory)

(accessory)

Ceiling slab



600

mm



310mm)

290

mm

1-1.5m



300mm

Hanger bracket

Adjustable

Drain raising pipe

Drain hose (accessory)

Metal clamp (accessory)

T-joint converging drain pipes

100mm

Portable pump

Water inlet lid

Close

Open

Bucket

Refrigerant
piping

Water inlet

01_EN_3P258319-5K.fm  Page 7  Thursday, October 15, 2015  11:03 AM

Summary of Contents for FXCQ20MVE















Reviews: