background image

8

English

(4) Making sure not to catch the horizontal flaps, remove the front grille by pulling in the direction of the arrow.

CAUTION

Remove the cardboard which is placed between filter and heat exchanger. Refer to figure below.

Remove the drain plug, the insulation tubing, and the drain hose from the drain pan and replace. 

(Refer to Fig. 8)

Connect the local refrigerant piping ahead of time, matching it to the liquid pipe and gas pipe marks 

engraved on the installation plate (1).

< Replacing the drain hose and drain plug >

(1) Remove the drain plug and insulation tubing.

(2) Remove the drain hose and replace onto the left side.

(3) Replace the drain plug and the insulation tubing onto the right side.

(6) Hook the indoor unit onto the installation plate. (Refer to Fig. 9)

Front grille

Fig. 7

Tab

(3)

(3)

(4)

(3)

Screw position (In case of FXAQ40,50,63 type)

(2)

(2)

(2)

Tab position

Cardboard

Tab position

Screw position

Drain plug

Insulating tube

Fig. 8

Do not place lubricant (refrigerant oil) when inserting. 
This may cause deterioration and water leaks.

Insert using a hexagon wrench (4mm).

Make sure 
there are 
no gaps.

4PEN494115-1A.book  Page 8  Tuesday, October 3, 2017  10:51 AM

Summary of Contents for FXAQ15AUV1B





























Reviews: