background image

English

4

Indoor Unit Installation Diagram

CAUTION

• Do not hit or violently push the INTELLIGENT EYE sensor. This can lead to damage and malfunction.

• Do not place large objects near the INTELLIGENT EYE sensor. Also keep heating units or humidifiers outside the sensor’s 

detection area.

Wrap the insulation pipe with the 

finishing tape from bottom to top.

Front grille

Hook

Bottom frame

Before screwing the 

      remote controller 

holder to the wall, 

make sure that 

control signals are 

properly received 

by indoor unit.

Service lid

The service lid is removable.

„

 Opening  method

1) Remove the service lid screws.

2) Pull out the service lid diagonally 

down in the direction of the arrow.

3) Pull down.

Cut thermal insulation pipe to an 

appropriate length and wrap it with tape, 

making sure that no gap is left in the 

insulation pipe’s cut line.

1-3/16” (30mm) or more 

from ceiling 

Upper front panel

1-15/16” (50mm) or more 

from walls (on both sides)  

Filter frame

Tab

Claw

Titanium apatite 

deodorizing filter

Air filter

Air filters

Screws M4 × 5/8” (M4 × 16mm)

C

D

Wireless remote controller

E

Remote controller 

holder

 

When dismounting the front grille, refer 

to 

“2. Removing and installing the front grille”

 

on page 11.

A

Mounting 

plate

INTELLIGENT EYE sensor

Screw covers

J

The       mounting plate should 

be installed on a wall which 

can support the weight of the 

indoor unit.

A

Mounting plate

„

 How to attach the indoor unit

Hook the hooks of the bottom 

frame to the       mounting plate.

If the hooks are difficult to hook, 

remove the front grille.

A

„

 How to remove the indoor unit

Push up the lower part of the 

front grille to release the hooks. 

If it is difficult to release, remove 

the front grille.

Mounting plate fixing 

screws M4 × 1” (M4 × 25mm)

B

F

Remote controller holder

fixing screws

M3 × 13/16” (M3 × 20mm)

Titanium apatite deodorizing filter (2)

A

E

Lower front panel

19-11/16” (500mm) 

or more

Make sure that there are no 

obstacles within 19-11/16 inch 

(500mm) under the signal 

receiver.

Such obstacles, if any, may have 

an adverse influence on the 

reception performance of the 

receiver and the reception 

distance may be shortened.

Do not connect commercially available 

drain hose directly to the indoor unit. 

(Water leakage may result)

01_EN_3P674703-1.fm  4 ページ  2022年3月29日 火曜日 午後3時40分

Summary of Contents for FTXR09WVJUW9

















Reviews: