background image

English

11

Installation Tips

1.

Removing and installing the upper front panel

2.

Removing and installing the front grille

CAUTION

Be sure to wear protection gloves.

• Removal method 

1) Remove the upper front panel and air filters.

2) Remove the service lid. (Refer to the opening method on page 4.)

3) Disconnect the wire harnesses from the wire clamp, and remove the wire 

harnesses from the connectors.

4) Push the lower front panel up until it stops.

5) Dismount the flap (large).

6) Open the 2 screw covers, and remove 4 screws from the front grille.

(The screw covers are not factory-mounted.) 

Back of the upper front panel

Front panel shaft

3-1) Slide

Shaft hole

3-2) Pull

Back of the upper front panel

2)  Slide

The upper front panel does not 
open any more than as shown in 
the 

fi

gure. Do not force it open 

any further than that.

Front panel lock

Removal method 

1) Open the upper front panel.
2) Slide the front panel locks on the back of the front panel upward 

to release the locks (left and right sides).

3) Remove the panel shafts on both sides from the shaft holes, and 

dismount the upper front panel.

Installation method 

1) Slide the front panel locks on the back of the front panel upward to release the 

locks (left and right sides).

2) Insert the panel shafts on both sides of the upper front panel into the shaft holes.
3) Slide the front panel locks on each side downward to lock them.
4) Close the upper front panel slowly. (See 

Fig. 1

)

5) Do not push on the panel to close it. (See 

Fig. 2

)

6) Turn on the unit using the remote controller. Wait till the upper and lower front 

panels are completely open. Then, turn off the unit using the remote controller 
again. (See 

Fig. 3

)

7) Once the both panels close completely, gently push the upper front panel to 

hook it into position. (See 

Fig. 4

)

Fig. 3

Fig. 4

ON/OFF

“clic

k”

“clic

k”

“clic

k”

“click”

“click”

Fig. 2

Fig. 5

Fig. 1

Do not attempt to push closed the front panel 
with the upper and lower front panels 
overlapping. Internal parts may break. 

(See 

Fig. 5)

If the front panel must be closed by hand for some 
reason (remote controller not functioning owing to 
lack of power supply, etc.), follow the instructions 
af

fi

xed to the indoor unit. 

CAUTION

Overlapping

(Viewed from side)

Wire clamp

Connectors

Wire harnesses

Flap (large)
Remove by pushing to the right while bending it slightly

4 screws

• Opening method

Use a long flat plate such as a 

ruler and wrap it in a cloth so 

as not to damage the product.

Downward

Screw covers

J

01_EN_3P674703-1.fm  11 ページ  2022年3月29日 火曜日 午後3時40分

Summary of Contents for FTXR09WVJUW9

















Reviews: