background image

14

TIMER Operation

Timer functions are useful for automatically switching the 
air conditioner on or off at night or in the morning. You can 
also use OFF TIMER and ON TIMER in combination.

To use OFF TIMER 
operation

Check that the clock is correct.
If not, set the clock to the present time. 
(page 9.)

1. Press “OFF TIMER button”.

is displayed.

blinks.

2. Press “TIMER Setting button” 

until the time setting reaches the 
point you like.

Every pressing of either button increases 
or decreases the time setting by 10 min-
utes. Holding down either button changes 
the setting rapidly.

3. Press “OFF TIMER button” 

again.

The TIMER lamp lights up.

To cancel the OFF TIMER Operation

4. Press “CANCEL button”.

 The TIMER lamp goes off.

NOTE

When TIMER is set, the present time is not displayed.

Once you set ON, OFF TIMER, the time setting is kept in the memory. (The memory is canceled when 
remote controller batteries are replaced.)

When operating the unit via the ON/OFF Timer, the actual length of operation may vary from the time 
entered by the user. (Maximum approx. 10 minutes)

NIGHT SET MODE

When the OFF TIMER is set, the air conditioner automatically adjusts the temperature setting (0.5°C 
up in COOL) to prevent excessive cooling for your pleasant sleep.

4

2

1, 3

01_EN_3P192025-3.fm  Page 14  Tuesday, October 10, 2006  4:58 PM

Summary of Contents for FT50FVM

























Reviews: