background image

13 Piping installation

Installation and operation manual

17

FHA-A(9)
Split system air conditioner
3P668115-4E – 2022.11

a

b

c

e

f

d

a

Round part

b

Rectangular part of the decoration side panel

c

Decoration side panel

d

Screw

e

Reinforcing plate

f

Right drain piping

Drain piping connection

b

a

d c b

f

d c b

f

A

A'

A

A'

4

2

c

d

e

5

90°

90°

A-A'

A-A'

A

B

1

3

2~5

1

a

Drain pipe connection (attached to the unit)

b

Drain hose (accessory)

c

Metal clamp (accessory)

d

Large sealing pad (accessory)

e

Drain piping (field supply)

f

Tightened part of metal clamp

A

In case of bending the end of the metal clamp

B

In case of wrapping the end of the metal clamp with vinyl
tape

1

Push  the  drain  hose  as  far  as  possible  over  the  drain  pipe
connection.

2

Tighten  the  metal  clamp  at  the  base  of  the  drain  socket.  Wrap
the  end  of  the  metal  clamp  with  vinyl  tape  or  bend  the  end
inwards to avoid damaging the sealing pad.

3

Check for water leaks (see 

"To check for water leaks"

 [

4

 17]).

4

Wind  the  large  sealing  pad  (=  insulation)  around  the  metal
clamp  and  drain  hose,  and  fix  it  with  tie  wraps.  Start  wrapping
from the tightened part of the metal clamp so that the end of the
metal clamp is wrapped twice.

5

Connect the drain piping to the drain hose.

To check for water leaks

Make  sure  the  unit  is  level  in  accordance  with  the  instructions  in

"12.2.1  Guidelines  when  installing  the  indoor  unit"

  [

4

  14].  Gradually

pour approximately 1 l of water through the air discharge outlet, and
check for leaks.

a

≥100

b

(mm)

a

Air outlet

b

Plastic water container with tube length ≥100 mm

13

Piping installation

13.1

Preparing refrigerant piping

13.1.1

Refrigerant piping requirements

CAUTION

Piping MUST be installed according to instructions given in

"13  Piping  installation"

  [

4

  17].  Only  mechanical  joints  (e.g.

braze+flare connections) that are compliant with the latest
version of ISO14903 can be used.

NOTICE

The  piping  and  other  pressure-containing  parts  shall  be
suitable  for  refrigerant.  Use  phosphoric  acid  deoxidised
seamless copper for refrigerant piping.

▪ Foreign materials inside pipes (including oils for fabrication) must

be ≤30 mg/10 m.

Refrigerant piping diameter

For  piping  connection  of  the  indoor  unit,  use  the  following  piping
diameters:

Pipe outer diameter (mm)

Class

Liquid pipe

Gas pipe

35

Ø6.4

Ø9.5

50+60

Ø6.4

Ø12.7

71~140

Ø9.5

Ø15.9

Refrigerant piping material

Piping material:

 phosphoric acid deoxidised seamless copper

Flare connections:

 Only use annealed material.

Piping temper grade and thickness:

Outer diameter

(Ø)

Temper grade

Thickness (t)

(a)

6.4 mm (1/4")

Annealed (O)

≥0.8 mm

t

Ø

9.5 mm (3/8")

12.7 mm (1/2")

15.9 mm (5/8")

(a)

Depending on the applicable legislation and the maximum
working pressure of the unit (see "PS High" on the unit name
plate), larger piping thickness might be required.

Summary of Contents for FHA35AVEB98





























Reviews: