background image

6 Installation

Installer reference guide

17

AZQS100~14 AZQS100~140B7Y1B
Split system air conditioners
4P385529-1B – 2016.10

To determine the additional refrigerant amount (R in kg)

L1 (m)

30~40 m

40~50 m

R:

0.5 kg

1.0 kg

INFORMATION

For  details  about  the  combination  of  your  outdoor  and
indoor unit, see the engineering databook.

6.6.4

To determine the complete recharge
amount

Model

L1 (m)

5~10

10~20

20~30

30~40

40~50

125

1.9

2.4

2.9

3.4

3.9

AZQS140

3.0

3.5

4.0

4.5

5.0

INFORMATION

For  details  about  the  combination  of  your  outdoor  and
indoor unit, see the engineering databook.

6.6.5

Charging refrigerant: Setup

See 

"6.5.3 Checking refrigerant piping: Setup" on page 15

.

6.6.6

To charge refrigerant

WARNING

▪ Only use R410A as refrigerant. Other substances may

cause explosions and accidents.

▪ R410A  contains  fluorinated  greenhouse  gases.  Its

global  warming  potential  (GWP)  value  is  2087.5.  Do
NOT vent these gases into the atmosphere.

▪ When  charging  refrigerant,  always  use  protective

gloves and safety glasses.

CAUTION

To  avoid  compressor  breakdown,  do  NOT  charge  more
than the specified amount of refrigerant.

Prerequisite: 

Before charging refrigerant, make sure the refrigerant

piping is connected and checked (leak test and vacuum drying).

1

Connect  the  refrigerant  cylinder  to  both  the  service  port  of  the
gas stop valve and the service port of the liquid stop valve.

2

Charge the additional refrigerant amount.

3

Open the stop valves.

If  pump  down  is  needed  in  case  of  dismantling  or  relocating  the
system, see 

"11.3 To pump down" on page 22

 for more details.

6.6.7

To fix the fluorinated greenhouse gases
label

1

Fill in the label as follows:

b

Contains fluorinated greenhouse gases

2

1

1

1

2

2

kg

tCO

2

eq

GWP × kg

1000

=
=

+

kg

=

kg

=

GWP: XXX

RXXX

a

f

c

d
e

a

If a multilingual fluorinated greenhouse gases label is
delivered with the unit (see accessories), peel off the
applicable language and stick it on top of 

a

.

b

Factory refrigerant charge: see unit name plate

c

Additional refrigerant amount charged

d

Total refrigerant charge

e

Greenhouse gas emissions

 of the total refrigerant charge

expressed as tonnes CO

2

-equivalent

f

GWP = Global warming potential

NOTICE

In  Europe,  the 

greenhouse  gas  emissions

  of  the  total

refrigerant  charge  in  the  system  (expressed  as  tonnes
CO

2

-equivalent)  is  used  to  determine  the  maintenance

intervals. Follow the applicable legislation.

Formula  to  calculate  the  greenhouse  gas  emissions:

GWP value of the refrigerant × Total refrigerant charge [in
kg] / 1000

2

Fix  the  label  on  the  inside  of  the  outdoor  unit.  There  is  a
dedicated place for it on the wiring diagram label.

6.7

Connecting the electrical wiring

6.7.1

About connecting the electrical wiring

Typical workflow

Connecting  the  electrical  wiring  typically  consists  of  the  following
stages:

1

Making  sure  the  power  supply  system  complies  with  the
electrical specifications of the units.

2

Connecting the electrical wiring to the outdoor unit.

3

Connecting the electrical wiring to the indoor units.

4

Connecting the main power supply.

6.7.2

About electrical compliance

A AZQS125_Y1

Equipment  complying  with  EN/IEC  61000‑3‑12  (European/
International  Technical  Standard  setting  the  limits  for  harmonic
currents  produced  by  equipment  connected  to  public  low-voltage
systems with input current >16 A and ≤75 A per phase.).

AZQS140_Y1

Equipment complying with:

EN/IEC  61000‑3‑12

  provided  that  the  short-circuit  power  S

sc

  is

greater  than  or  equal  to  the  minimum  S

sc

  value  at  the  interface

point between the user's supply and the public system.

▪ EN/IEC 

61000‑3‑12 

European/International 

Technical

Standard  setting  the  limits  for  harmonic  currents  produced  by
equipment  connected  to  public  low-voltage  systems  with  input
current >16 A and ≤75 A per phase.

▪ It is the responsibility of the installer or user of the equipment to

ensure, by consultation with the distribution network operator if
necessary,  that  the  equipment  is  connected  only  to  a  supply
with  a  short-circuit  power  S

sc

  greater  than  or  equal  to  the

minimum S

sc

 value.

Model

Minimum S

sc

 value

AZQS140_Y1

1170 kVA

(a)

(a)

This is the most stringent value. For specific product data,
see the databooks.

Summary of Contents for AZQS140B8V1B





























Reviews: