background image

IOM 1178-1 / Page 15 of 16

Programming

Averaging or Weighing Remote Sensors

The thermostat will weight or average the temperature of the 
indoor remote sensor with the local sensor in the thermostat 
for each program period. The averaging will be active only 
when the local sensor and the indoor remote sensor are both 

functional and enabled in the Installer/Configuration menu.
When the thermostat is in the Set Schedule mode, the weight 

of the indoor sensor will be shown in the current temperature 
digits of the display. The weight will show as A2 (average and 

default), H4 (high) or L1 (low). Pressing the and keys at the 

same time will change the weight for the program period. The 

weight of the thermostat sensor is fixed.

In normal operation of the thermostat, the current temperature 
displayed will be the weighted average of the local sensor and 
the remote sensor using the formula (local sensor weight × 
local sensor temperature) + (remote sensor weight × remote 
sensor temperature) / (local sensor remote sensor 
weight).

Example:

 Local sensor temperature is 80° and the remote 

sensor is 70°.

If weight is selected H4, the averaged temperature of 72° will 

be displayed.

(1 × 80) + (4 × 70) / 5 = 72°

If weight is selected A2, the average temperature of 73° will 
be displayed.

(1 × 80) + (2 × 70) / 3 = 73.3°

If weight is selected L1, the average temperature of 75° will 
be displayed.

(1 × 80) + (1 × 70) / 2 = 75°

The example shows that the weight selected would prioritize 
the overall averaged temperature between the two sensors.

The high weight selection caused the remote sensor to have 

a higher influence in the calculated temperature average than 

the local sensor and the low weight selection caused the 

remote sensor to have less influence.

Summary of Contents for 910121750

















Reviews: