Daihatsu TERIOS J100 Service Manual Download

Page: 87 / 96

7. Connection of the fuel hoses to fuel pump assembly

(1) Connection of the fuel main tube

Clean the fuel main pipe on the fuel pump assem-
bly.

Apply the few drops of engine oil to the fuel pipe.

Connect the new fuel hose to the fuel pipe until
clicking sounds emits from the retainer.

Remove the checker from the quick connector.

Ensure that the connector is connected properly
by pull the connector from the fuel pipe lightly.

(2) Connect the fuel main tube to the fuel pipe clamps in-

stalled on the fuel tank securely.

(3) Connection of the fuel return tube

Ensure that the checker of the quick connector is
installed on the quick connector as shown.

Clean the fuel return pipe on the fuel pump assem-
bly.

Apply the few drops of engine oil to the fuel pipe.

Connect the new fuel hose to the fuel pipe until
clicking sounds emits twice.

BO–87

Pull this up

JBO00235-00201

JBO00236-00202

JBO00237-00203

JBO00238-00204

JBO00239-00205

Summary of Contents for TERIOS J100

































































































Search results

Summary of Contents for TERIOS J100

Reviews:

Related manuals for TERIOS J100

Brands by name

Popular brands

Daihatsu TERIOS J100, Service Manual

Search results

Summary of Contents for TERIOS J100

Reviews:

Related manuals for TERIOS J100

Brands by name

Popular brands