background image

15. Install the rear door glass outer weatherstrip to the rear door panel by connecting the rear door glass

weatherstrip clip to the rear door panel.

16. Install the rear door regulator subassembly with the attaching bolts.
17. Install the rear door window regulator handle temporarily.
18. Align the position for the rear door glass attaching bolts with the hole on the rear door panel.
19. Install the rear door glass subassembly to the rear door panel.
20. Install the attaching bolts of the rear door glass to the rear door window regulator subassembly.
21. Install the rear door window guide subassembly into the rear door panel and connect the rear window

glass run to the rear door window guide subassembly.

22. Install the rear door window guide subassembly to the rear door panel while inserting the rear door win-

dow glass into the glass run.

23. Install the rear door lower frame seal by connecting its retainers to the rear door panel assembly.
24. Connect the connector of the rear door wire to the door control motor assembly.
25. Install the rear door glass weatherstrip assembly to the rear door trim panel assembly by bending the

protrusion sections on the front door glass weatherstrip assembly.

26. Installation of rear door service hole cover

(1) Affix a butyl tape to the groove provided around the rear door panel as shown.

CAUTION:

·

Care must be exercised so that the joint section of the butyl tape may come at the upper section. If
the joint section of the tape comes at the lower side of the door, it may cause water leakage.

·

The butyl tape should be routed just under the water drain holes. Failure to observe this caution may
lead to collection of water, resulting in rust formation.

·

Never reuse the removed service hole cover.

(2) Affix the front door service hole cover, as shown.

NOTE:

·

Pass the rear door open control link through the front door service hole cover during the assembly.

BO–57

A

B

Align with beads.

Cover

Section A

Cover assembling reference

Align with beads.

Cover

Section B

Align with butyl location.

JBO00150-00000

JBO00151-00129

Summary of Contents for TERIOS J100

































































































Reviews: