background image

1. SAFETY INSTRUCTIONS 

Read all instructions before using this appliance and save the operation instruction

WARNING: 

when using this product, basic precaution should always be followed, including the 

following:

 

1. Don’t use the appliance without reading the instruction sheet.

 

2. Risk of injection or injury do not direct discharge stream at persons.
3. It is recommended that the electric supply to this appliance should include either a residual current  
Device that interrupt the supply if the leakage current to earth exceeds 30 ma for 30 ms or a device 
Which will prove the earth circuit.
4. Do not use the appliance within the range of persons unless they wear protective clothing.

5. High-pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, 
Animals, electrical equipment or the appliance itself.

6. Don’t direct the jet against yourself or others in order to clean clothes or foot-wear.
7. Disconnect from the electrical power supply before carrying out user maintenance.
8. High-pressure cleaners shall not be used by children or untrained personnel.

 

9. To ensure the appliance safety

use only original spare parts from the manufacturer or approved by 

  

The manufacturer

10. High-pressure hoses fittings and couplings are important for the safety of the appliance. Use only
Hoses, fittings and couplings recommended by the manufacturer.

11. Don’t use the appliance if a supply cord or important parts of the appliance are damaged, e.G. 
Safety
De vices, high-pressure hoses, trigger gun.
12. Inadequate extension cords can be dangerous.

 

13. If an extension cord is used, the plug and socket must be of watertight construction.
14. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a 
Similarly qualified person in order to avoid a hazard.
15. To reduce the risk of injury, close supervision is necessary when a product is used near children
16. Know how to stop the product and release pressure quickly, be thoroughly familiar with the controls.
17. Stay alert-watch what you are doing.

18. Do not operate the product when fatigued or under the influence of alcohol or drugs.

19. Keep operating area clear of all persons.

20. Do not overreach or stand on unstable support. Keep good footing and balance at all times.

21. Follow the maintenance instructions specified in the manual.

22. This product shall only be connected to a power supply receptacle produced by a ground fault 
circuit.

Interrupter

23. Always wear protective clothing and safety glasses. Loose particles and other debris may be 
Propelled at high speed by the water jet. Wear ear protectors. 
24. The electric supply connection shall be made by a qualified electrician and comply with iec 60364-1
25. This appliance has been designed for use with the cleaning agent supplied or recommended by the 
manufacturer. The use of other cleaning agents or chemicals may adversely affect the safety of the 
appliance.
26. If an H05VV-F or H05V2V2-F supply cord is used, the appliance must be used at or above 0°C

.

2

EN

Summary of Contents for DAV100A























Reviews: