background image

2

NOTE:

All dimensional tolerances are 

+ 1/16”, - 0” unless otherwise 

stated. (Metric dimensions are for 

reference only.)

Verifying the Package Contents

•   Use and Care manual

• 

Dacor nameplate

•   Hardware for changing door swing

•   Left and right side hinge covers

•   Top screw hole cover

Installation Planning

A qualified technician must complete the 

installation of this built-in appliance. Proper 

installation is your responsibility.

Carefully check the location where the appliance 

is to be installed. The appliance should be 

placed for convenient access. Make certain that 

electrical power can be provided in the selected 

location.

Plan the installation so that all minimum 

clearances are met or exceeded. Dimensions 

shown provide minimum clearances, unless 

otherwise noted. Be certain that proper 

clearance is provided for the appliance door 

when it is in the open position.

The specified minimum cabinet depth and width 

must be provided.

Cabinet cutout dimensions must be used as 

indicated. All contact surfaces between the 

appliance and the cabinet must be solid and 

level.

Make certain that you have everything 

necessary to ensure a proper installation before 

proceeding.

Overall Dimensions

(EWC, EBC)

Product Clearances

The wine chiller, wine reserve and beverage 

center is factory set for a 110° door swing.

When installed in a corner:

•   Allow 4” min. clearance on the hinge 

side for the 90° door swing and to 

allow racks to slide out.

•   Allow 10” minimum clearance on the 

hinge side for a full 110° door swing.

21 5/8”

(651mm)

23 5/8”

(600mm)

4“ Minimum to Wall

(102mm)

90°

10” Minimum to Wall

(254mm)

110°

Choose the location:

•   These products may be closed in on 

the top and three sides as long as the 

front is unobstructed for air circulation 

and proper access to the door.

•   Do not install these products where 

the temperature will go below 55°F 

(13°C) or above 90°F (32°C).

•   Do not install where it will be subject 

to direct sunlight, heat or moisture.

23 3/4”

(603mm)

34 1/2” - 35”

(876mm - 597mm)

23 3/4”

(603mm)

•   The door swing is reversible on all 

models. If desired, change the door 

swing before installation.

Summary of Contents for Wine Steward/Beverage Cooler









Reviews: