background image

15

Appendix A: Screen Adjustment for Type 2 Motor (LT suffix in Part Number)

No manual limit adjustments 
on end of motor

RJ-22 cable

3-wire connection

TYPE 2 MOTOR

TYPE 2 WALL SWITCH

1.  Remove the cover plate from the 3-button wall switch and 

remove the switch from the junction box.

2.  Locate small 3-position switch on back of wall switch. 

3.  To adjust the down limit switch, slide the 3-position switch to the 

down position. Press and hold the down button to run the screen 
down to the desired stop position. Release the button to stop the 
screen. DO NOT PUSH THE STOP BUTTON.

 

CAUTION: Do not adjust for more drop than what was 
ordered. At least 1–1/2 wraps of fabric must remain on the 
roller. This screen comes standard with 12" black at the top.

4.  When the screen is in the desired down position, slide the 

3-position switch to the off (center) position. The down limit 
switch is now set.

5.  To adjust the up limit switch, slide the 3-position switch to the up 

position. Press and hold the up button to run the screen up to 
the desired stop position. Release the button to stop the screen. 
DO NOT PUSH THE STOP BUTTON.

 

CAUTION: Adjusting the limits by more than 6” can cause the 
screen surface to lose proper tensioning.

6.  When the screen is in the desired up position, slide the 3-position 

switch to the off (center) position. The up limit switch is now set.

7.  To test limit switch setting, make sure the 3-position switch is in 

the off (center) position. Press and release the up or down button 
on the wall switch to operate the screen.

8.  Replace switch and cover plate on the wall.

 NOTE: 

If stop button is pressed, the wall switch will reverse 

direction. To correct this, press the stop button again. This will 
reset the switch. You will have to reset both the up and the down 
limit settings.

 

IMPORTANT NOTE: 

The wall switch is REQUIRED to make any 

limit switch adjustments, even  if a third party control system is 
used. Therefore, it is advised to wire the switch or provide a 
4-conductor connection that is accessible.

RJ-22

3-Position 

Switch

DN

GND +5V

UP

Back of Wall Switch

Summary of Contents for ViewShare





















Reviews: