background image

3

TENSIONED COSMOPOLITAN

®

  ELECTROL

®

  INSTALLATION

120V WIRING DIAGRAM WITH  

OPTIONAL BUILT-IN VIDEO  

PROJECTOR INTERFACE

5/12 VOLT SCREEN 

TRIGGER ON PROJECTOR

CAUTION: THE PROJECTOR MUST BE TURNED OFF BEFORE CONNECTING THE TRIGGER 
WIRES TO THE PROJECTOR. FAILURE TO DO SO MAY DAMAGE THE CONTROLLER.

 Use 2-conductor 20-24 gauge wire to extend the low voltage connection from 
the projector’s 5 or 12-volt screen trigger output to the length required to reach 
the VPI. When extending the low voltage connection from the projector’s screen 
trigger output polarity does not matter. The red and black wires from the VPI are 
interchangeable. 

GROUND–MUST BE CONNECTED 

TO BUILDING GROUND

UP

STOP

DOWN

POWER INPUT 120VAC / 60HZ

GREEN (GROUND)

BLACK (HOT)

WHITE (COMMON)

POWER 

WIRE

DATA

CABLE

RJ-45 

JACK

RJ-45

RECEPTACLE

RJ-22 OUTPUT 

RJ-22 JACK 

RJ-22

INPUTS 

RJ-22

JACK

LED

UP LIMIT

TACTILE 

BUTTON

DOWN 

LIMIT

TACTILE 

BUTTON

FRONT OF 

WALL SWITCH

BACK OF

WALL SWITCH

DRY CONTACTS 

UP (RED)

 

DO

WN (BLA

CK)

 

COMMON 

(WHI

TE)

BLACK 

RED

VPI TRIGGER 

MODULE

IMPORTANT NOTE:

 

The wall switch is REQUIRED to make any limit switch adjustments, 
EVEN if a third party control system is used.  Therefore, it is advised to 
wire the switch or provide a 3-conductor connection that is accessible.

FIGURE 4

120V WIRING DIAGRAM 

WITH OPTIONAL BUILT-IN 

LOW VOLTAGE CONTROL

GROUND–MUST BE 

CONNECTED TO 

BUILDING GROUND

RJ-14 PIN-OUTS

(TAB IS FACING UP)

FIGURE 5

IMPORTANT NOTE:

 

The wall switch is REQUIRED to make any limit switch 

adjustments, EVEN if a third party control system is 

used.  Therefore, it is advised to wire the switch or 

provide a 3-conductor connection that is accessible.

UP

STOP

DOWN

POWER INPUT 120VAC / 60HZ

GREEN (GROUND)

BLACK (HOT)

WHITE (COMMON)

POWER WIRE

DATA

CABLE

RJ-45 JACK

RJ-45

RECEPTACLE

RJ-22

OUTPUT 

RJ-22

JACK 

RJ-22

INPUTS 

RJ-22

JACK

LED

UP LIMIT

TACTILE BUTTON

DOWN LIMIT

TACTILE BUTTON

FRONT OF 

WALL SWITCH

BACK OF

WALL SWITCH

RJ-22 PIN-OUTS

(TAB IS FACING UP)

RJ-45 PIN-OUTS

(TAB IS FACING UP)

Standard RJ-22 can be used in place of RJ-14

Supplied RJ-14 cable

BLUE
YELLOW
GREEN
RED
BLACK
WHITE

+12V

BUS (RP DATA)

RQ DATA

+5V

GND

RQ CLOCK

BUS (RP DATA)

RQ DATA

+5V

GND

WHITE
GREEN
RED
BLACK

BLUE
YELLOW
GREEN
RED
BLACK
ORANGE

BROWN

PURPLE

+12V

BUS (RP DATA)

RQ DATA

+5V

GND

RQ CLOCK

MANUAL 1

MANUAL 2

DRY CONTACTS 

UP (RED)

 

DOWN (BLACK)

 

COM (WHITE)

 

Summary of Contents for TENSIONED COSMOPOLITAN ELECTROL









Reviews: