background image

7

Printed in U.S.A. 

76063 Rev. 2/10

LIMITED ONE YEAR WARRANTY

ON DA-LITE PRESENTATION PRODUCTS

Da-Lite Screen Company, Inc. warrants its products to the original purchaser only, to be free from 

defects in materials and workmanship for a period of one (1) year from the date of purchase by 

the original purchaser provided they are properly operated according to Da-Lite’s instructions and 

are not damaged due to improper handling or treatment after shipment from the factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental 

damage, or which has been tampered with or repaired by a person other than authorized Da-Lite 

personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) 

the defective part of the merchandise.  Returns for service should be made to your Da-Lite dealer.  

If it is necessary for the dealer to return the screen or part to Da-Lite, transportation expenses 

to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in 

shipment.  To protect yourself against damage or loss in transit, insure the product and prepay all 

transportation expenses.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, 

INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY.

  Any implied 

warranties of fitness for use, or merchantability, that may be mandated by statute or rule of law 

are limited to the one (1) year warranty period.  This warranty gives you specific legal rights, and 

you may also have other rights, which vary from state-to-state.  

NO LIABILITY IS ASSUMED 

FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF 

EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY 

NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may 

contact our Sales Partners at PO Box 137, Warsaw, IN  46581-0137, (574) 267-8101, (800) 622-3737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE SHALL NOT BE 

BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH  

DA-LITE’S WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

Summary of Contents for TENSIONED COSMOPOLITAN ELECTROL









Reviews: