D-Link xStack Hardware Installation Manual Download Page 20 | Manualshive

Page: 20 / 71

background image

xStack® DGS-3420 Series Layer 2+ Managed Stackable Gigabit Switch Hardware Installation Reference Guide

19

Installing the Switch without a Rack

First, attach the rubber feet included with the Switch if installing on a desktop or shelf. Attach these cushioning feet on the
bottom at each corner of the device. Allow enough ventilation space between the Switch and any other objects in the
vicinity.

Figure 2–1 Attach rubber feet to the switch.

Attaching Brackets to a Switch for Rack Mounting

The Switch is mounted to a standard 19" rack using mounting brackets. Use the following diagrams as a guide.

Figure 2–2 Attach mounting brackets to the switch

Fasten the mounting brackets to the Switch using the screws provided. With the brackets attached securely, the Switch
can be mounted in a standard rack, as shown below.

NOTE:

Please review the Installation Guidelines above before installing the Switch in a rack. Make

sure there is adequate space around the Switch to allow for proper air flow, ventilation and cooling.

«
...
18
19
20
21
22
...
»

Summary of Contents for xStack








































































Reviews:

No comments

Related manuals for xStack

Brand: NEC Pages: 16

Brand: Panasonic Pages: 89

Brand: Skytec Pages: 12

Brand: Looperlative Pages: 29

StorEdge S1 Array

Brand: Sun Microsystems Pages: 32

Brand: Pioneer Pages: 85

Brand: Pioneer Pages: 90

Brand: Pioneer Pages: 152

Brand: Pioneer Pages: 166

Brand: Pioneer Pages: 468

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands