background image

96

DCS-950G User’s Manual 

D-Link Systems, Inc.

Warranty

FCC Statement

:  This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can radiate 
radio frequency energy and, if not installed and used in accordance with the instructions, may cause 
harmful interference to radio communication. However, there is no guarantee that interference will not 
occur in a particular installation. If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user is encouraged to try 
to correct the interference by one or more of the following measures:

 

 Reorient or relocate the receiving antenna.

 

 Increase the separation between the equipment and receiver.

 

 Connect the equipment into an outlet on a circuit different from that to which the receiver is  

 

 

connected.

 

 Consult the dealer or an experienced radio/TV technician for help.

For detailed warranty outside the United States, please contact corresponding local D-Link office. 

FCC Caution: 

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications 
to this equipment; such modifications could void the user’s authority to operate the equipment.

(1) The devices are restricted to indoor operations within the 5.15 to 5.25GHz range. (2) For this device 
to operate in the 5.15 to 5.25GHz range, the devices must use integral antennas.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.

IMPORTANT NOTE:  

FCC Radiation Exposure Statement: 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.  
The antenna(s) used for this equipment must be installed to provide a separation distance of at least 
eight inches (20 cm) from all persons. 

This equipment must not be operated in conjunction with any other antenna.

Summary of Contents for SECURICAM Network DCS-950G


































































































Reviews: