D-Link DVG-4032S User Manual Download | Manualshive

Page: 22 / 50

background image

19

Network Settings (LAN)

Network Settings (LAN): Gateway LAN Port IP address and the subnet mask value.
Please note that Gateway is built under NAT: Gateway LAN Port IP address cannot be
in the same section as the NAT LAN Port IP address, or else it is unable to make or
receive calls. For example, if the NAT LAN Port IP address is 192.168.8.1, then
Gateway LAN Port cannot be ranged between 192.168.8.1 ~ 192.168.8.254. If so,
please change the LAN port IP address, (e.g. setting the IP address to 192.168.99.254.)

Port of Web Access from WAN: Http port for WAN. To make this setting, the LAN Port
must be used. Settings cannot be made using the WAN Port. Always use port 80 when
connecting to LAN port.

QoS Settings

QoS (Quality of Service): Sets an external bandwidth to ensure sound quality during
transmission (When this function is enabled, the voice packet has the highest priority to
ensure telecommunication quality while less bandwidth is assigned for data
transmission).

ToS/DiffServ (Type of Service/DSCP): The voice packet has the highest priority to
ensure telecommunication quality; the larger the value you set, the higher priority you
will get.

«
...
20
21
22
23
24
...
»

Summary of Contents for DVG-4032S



















































Reviews:

No comments

Related manuals for DVG-4032S

Brand: QTS Pages: 62

ServiceRouter V2

Brand: Eurogard Pages: 23

Brand: Hypercom Pages: 2

Brand: XAVi Pages: 51

VBG-PN-K20-DMD-EV

Brand: Pepperl+Fuchs Pages: 11

Brand: VBOX Pages: 11

Ositech Titan II

Brand: Ositech Communications Pages: 4

Brand: NEP Pages: 6

SMART/RG SR555ac

Brand: ADTRAN Pages: 154

BEST Wi-Q WQXM-PG

Brand: Dormakaba Pages: 51

Brand: Schwaiger Pages: 24

Brand: TASHI Pages: 2

Fieldgate PAM SFG600

Brand: Endress+Hauser Pages: 20

MediaAccess TG789vn

Brand: Technicolor Pages: 128

PowerMaster-360

Brand: Visonic Pages: 65

Lucent Technologies Access Security Gateway Guard

Brand: BELL LABS INNOVATIONS Pages: 266

Brand: Deco Pages: 22

SURFboard SBG6700-AC

Brand: Arris Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands