5
Racking
Speaker cable connections
Input cable connections
Power consumption
Cooling
Either
the
binding
posts
or
the
Speakon
connectors (
and
)
can be
used.
The binding posts can be used with bare wire or
banana connectors. In either case, ensure that you
remove the required length of cable sleeve that allows
for the conductor itself to be hidden. Always note
polarity (red=+,black=–).
Speakon connectors offer quick connection for
portable
applications.
To
enable
a
Speakon
connection, plug the male connector into the outlet
and rotate it clockwise. It will then lock into place and
be ready for use.
The Appendices of this manual include a table to
aid in the selection of the appropriate cable gauge.
PS-800,PS-1400
PS-2400
A fan cools the aluminium heat
sinks from back to front.
Fan
cooling
permits
airflow
through the most vital parts of the
amplifier.
When mounting the unit onto a
19-inch
rack,
a
rack
cooling
system is not required, since the
air is exhausted out through the
front grille.
However, the rack must not be
sealed, and it should at least have
a large enough ventilation grille to
allow air into the rack.
All amplifiers are 19-inch rack mount width.
and
are 1U DIN in height.
,
and
are 2U DIN in height.
Four front-panel mounting holes are provided for
use with M5 or M6 or 1/4” screws. To avoid bending
the chassis in rack mounting applications where the
rack will be transported, mount the amplifiers to the
back of the rack using the rear mounting holes.
Alternatively, place the bottom amplifier against the
base of the rack and pile the amplifiers with no
clearance in between.
Amplifier’s dimensions can be found on the “Line
Drawings” section of this manual.
PS-200
PS-400
PS-800 PS-1400
PS-2400
Can be seen on the accompanying table for 230V.
Double
the
ratings
to
get
the
115V
current
consumption.
Standard
specify
AC
consumption using pink noise at 1/8th of rated power.
IEC-60065:2001
This is done to represent the current requirements to
reproduce a typical musical programme.
The 1/3rd power rating represents a worst case
scenario,
while
the
maximum
power
represents
consumption with sine wave signal, which will never
occur in practice.
The Input Cabling Appendix shows balanced and
unbalanced
connection
from
different
types
of
connector to the amplifiers.
Nominal AC voltage will always be indicated on the
back panel. 230V and 115V versions are available.
range on 230V version, is
230V ±10%, that meaning it can work from
Likewise, on the 115V version, the nominal AC
voltage range is 115
Nominal AC voltage
207V up
to 253V.
V ±10%, that meaning it can work
from 103V up to 127V.
Be sure your unit has the nominal AC voltage for
your country.
INSTALLATION
Connection to mains
EN
Consumos eléctricos / Power consumption (Amperios / Amperes)
Potencia / Power
Max
1/3
1/8
Sin señal
/ idle
PS-200
Puente/
Puente/
Puente/
Puente/
Puente/
bridge
bridge
bridge
bridge
bridge
PS-400
PS-800
PS-1400
PS-2400
8+8 ohm
0.87
0.31
0.15
0.05
8+8 ohm
1.64
0.57
0.27
0.08
8+8 ohm
2.8
0.98
0.48
0.15
8+8 ohm
5.2
1.82
0.84
0.2
8+8 ohm
12.8
5.9
2.8
0.5
4+4 ohm
1.57
0.57
0.25
0.05
4+4 ohm
2.98
1.06
0.47
0.08
4+4 ohm
5.28
1.82
0.81
0.15
4+4 ohm
9.59
3.41
1.48
0.2
4+4 ohm
20.1
9.6
4.8
0.5
2+2 ohm
---
---
8.5
0.5
8 ohm
1.6
0.6
0.25
0.05
8 ohm
3.0
1.1
0.5
0.08
8 ohm
5.3
1.85
0.85
0.15
8 ohm
9.6
3.45
1.5
0.2
8 ohm
20.5
9.6
4.7
0.5
Manual del Usuario
/ PS /
User’s Manual
Summary of Contents for PS Series
