Cypress Semiconductor CY8C23433 Specification Sheet Download Page 1

Page: 1 / 37

CY8C23433, CY8C23533

PSoC

Programmable System-on-Chip™

Cypress Semiconductor Corporation

•

198 Champion Court

•

San Jose

CA 95134-1709

•

408-943-2600

Document Number: 001-44369 Rev. *B

Revised December 05, 2008

Features

■

Powerful Harvard Architecture Processor

❐

M8C Processor Speeds to 24 MHz

❐

8x8 Multiply, 32-Bit Accumulate

❐

Low Power at High Speed

❐

3.0 to 5.25V Operating Voltage

❐

Industrial Temperature Range: -40°C to +85°C

■

Advanced Peripherals (PSoC Blocks)

❐

4 Rail-to-Rail analog PSoC Blocks Provide:
• Up to 14-Bit ADCs
• Up to 8-Bit DACs
• Programmable Gain Amplifiers
• Programmable Filters and Comparators

❐

4 Digital PSoC Blocks Provide:
• 8 to 32-Bit Timers, Counters, and PWMs
• CRC and PRS Modules
• Full-Duplex UART
• Multiple SPI

™

Masters or Slaves

• Connectable to All GPIO Pins

❐

Complex Peripherals by Combining Blocks

❐

High-Speed 8-Bit SAR ADC Optimized for Motor Control

■

Precision, Programmable Clocking

❐

Internal ±2.5% 24/48 MHz Oscillator

❐

High Accuracy 24 MHz with Optional 32 kHz Crystal and PLL

❐

Optional External Oscillator, up to 24 MHz

❐

Internal Oscillator for Watchdog and Sleep

■

Flexible On-Chip Memory

❐

8K Bytes Flash Program Storage 50,000 Erase/Write Cycles

❐

256 Bytes SRAM Data Storage

❐

In-System Serial Programming (ISSP)

❐

Partial Flash Updates

❐

Flexible Protection Modes

❐

EEPROM Emulation in Flash

■

Programmable Pin Configurations

❐

25 mA Sink on all GPIO

❐

Pull up, Pull Down, High Z, Strong, or Open Drain Drive
Modes on All GPIO

❐

Up to Ten Analog Inputs on GPIO

❐

Two 30 mA Analog Outputs on GPIO

❐

Configurable Interrupt on All GPIO

■

Additional System Resources

❐

™

Slave, Master, and Multi-Master to 400 kHz

❐

Watchdog and Sleep Timers

❐

User-Configurable Low Voltage Detection

❐

Integrated Supervisory Circuit

❐

On-chip Precision Voltage Reference

■

Complete Development Tools

❐

Free Development Software (PSoC Designer™)

❐

Full-Featured In-Circuit Emulator and Programmer

❐

Full Speed Emulation

❐

Complex Breakpoint Structure

❐

128K Bytes Trace Memory

DIGITAL SYSTEM

SRAM

256 Bytes

Interrupt

Controller

Sleep and
Watchdog

Multiple Clock Sources

(Includes IMO, ILO, PLL, and ECO)

Global Digital Interconnect

Global Analog Interconnect

PSoC CORE

CPU Core (M 8C)

SROM

Flash 8K

Digital

Block
Array

Multiply
Accum.

Internal
Voltage

Ref.

Digital

Clocks

POR and LVD

System Resets

Decimator

SYSTEM RESOURCES

ANALOG SYSTEM

Analog

Ref

Analog

Input

Muxing

Port 2

Port 1

Port 0

Analog
Drivers

System Bus

Analog

Block Array

1 Row

4 Blocks

2 Columns

4 Blocks

SAR8 ADC

Port 3

Logic Block Diagram

[+] Feedback

Summary of Contents for CY8C23433






































Search results

Summary of Contents for CY8C23433

Reviews:

Related manuals for CY8C23433

Brands by name

Popular brands

Cypress Semiconductor CY8C23433, Specification Sheet

Search results

Summary of Contents for CY8C23433

Reviews:

Related manuals for CY8C23433

Brands by name

Popular brands