CYBEX 600T, Service Manual

Page: 47 / 55

-
-
Cybex 600T Treadmill Service
Manual
c.
Put the connector into the entry hole and push the twisted part
down. Bend the remaining cable in half as you feed it into the tube.
D. When the connector emerges at the bottom of the upright, gently
pull it out of the exit hole.
E. Locate the lower control in the base of the treadmill. Plug the
connector into the lower control board. See Figure 17.
F. Connect the male and female cables at the junction. See Figure 17.
9. Attach the motor cover.
A. Place the rear of the motor cover in the rear guide holes.
B. Lower the front end of the motor cover and install the two Phillips
head screws that hold it in place.
10. Replace the covers and accessory holder.
A. Attach the console cover with the eleven Phillips head screws on the
console back. See Figure 15.
B. Locate the position for the junction covers. Replace the four Phillips
head screws on the left junction covers.
Display Overlays
NOTE: This procedure will cover the upper and the lower display overlay.
You may need to replace one or both. See "Test Mode" in the
Troubleshooting chapter to determine which display needs
replaced.
Tools Required
• Phillips head screwdriver
1. Turn the power off.
A. Turn the main power switch in the front panel to the off (0) position.
B. Unplug the treadmill from the power outlet.
2. Remove the console back.
A. Remove the eleven Phillips head screws on the console back. Leave
the top which holds the accessory holder in place. The top
screw WIll keep the accessory holder in place on the console back.
Set the console back and screws aside. See Figure 15.
Table of Contents
i
Read All Instructions & Warnings
ii
Important Safety Instruct i ons
iv
About This Manual
Important Voltage Infonnation. iv
FCC Compliance Infonnation . iv
V Declaration of Confonnity
vii
Table of Contents
1
Safety
Warning Decals. . . . . . . . . . . 1-1
Caution Decals . . . . . . . . . . . 1-2
2
Technical Specifications
Specifications 2-1
3
Preventative Maintenance
Regular Maintenance Activities
3-1
Running Belt Maintenance.. 3-3
4
Troubleshooting
Test Mode 4-1
LED Functions. . . . . . . . . .. 4-1
Key Functions . . . . . . . . . . . 4-2
Error Codes. . . . . . . . . . . .. 4-2
Speed Sensor Adjustments . 4-3
5
Removal
&
Replacement
Running Deck . . . . . . . . . . .. 5-1
Running Belt . . . . . . . . . . . .. 5-5
Front Roller. . . . . . . . . . . . . . 5-5
Drive Belt. . . . . . . . . . . . . . .. 5-5
Rear Roller . . . . . . . . . . . . . .. 5-6
Drive Motor . . . . . . . . . . . . .. 5-7
Motor Brush . . . . . . . . . . .. 5-10
Elevation Motor 5-13
Lower Control Board 5-15
Power Cables 5-16
Une Riter 5-17
Power Switch 5-17
Power Cord Inlet 5-18
Display Board 5-18
Heart Rate Board 5-20
Lower Display Board 5-21
Polar Board 5-21
Upper Display Cable 5-22
Lower
Display Cable
5-24
Display
Overlays
5-25
6
Diagrams
Parts Ust . . . . . . . . . . . . . . . 6-1
Exploded
6-3
600T Schemat i c 6-4
7
Customer Service
Contacting Serv i ce . . . . . . .. 7-1
Serial Number
&
Voltage .. " 7-1
Return Material Authorization
(RMA)
7-1
Darnaged Parts "
8/ndex 8- "