background image

Effective 2/2/2001

Page 32

I.L. 70C1037H03

NOTICE

THE PROVISION FOR ZONE INTERLOCKING IS STAN-

DARD ON MAGNUM CIRCUIT BREAKERS WITH DIG-

ITRIP 520 FAMILY TRIP UNITS FOR SHORT TIME AND

GROUND FAULT FUNCTIONS. THE APPROPRIATE

JUMPER TO TERMINAL B8 AND B9 MUST BE ADDED

ON THE BREAKER IF ZONE INTERLOCKING IS NOT
DESIRED OR IF FIELD TESTING IS DESIRED.

APPENDIX A  Zone Interlocking Examples

CASE 1: There is no Zone Selective Interlocking.

(Standard time delay coordination is used.)

Assume that a ground fault of 2000 Amperes occurs and
refer to Figure A.1.

Fault at location 3

The branch breaker will trip, clearing the fault in 0.1
seconds.

Fault at location 2

The feeder breaker will trip, clearing the fault in 0.3

seconds.

Fault at location 1

The main breaker will trip, clearing the fault in 0.5 seconds.

CASE 2: There is Zone Selective Interlocking.

Assume a ground fault of 2000 Amperes occurs and refer

to Figure A.1.

Fault at location 3

The branch breaker trip unit will initiate the trip in

0.045 seconds to clear the fault and the branch will send a

restraint signal to the feeder trip unit; the feeder will send a

restraint interlocking signal to Z1.

Main and feeder trip units will begin to time out and, in the

event that the branch breaker does not clear the fault, the

feeder breaker will clear the fault in 0.3 seconds (as

above). Similarly, in the event that the feeder breaker does

not clear the fault, the main breaker will clear the fault in

0.5 seconds (as above).

Fault at location 2

The feeder breaker trip unit will initiate the trip in

0.045 seconds to clear the fault and will send an interlock-

ing signal to the main trip unit. The main trip unit will begin

to time out and, in the event that the feeder breaker Z2

does not clear the fault, the main breaker will clear the

fault in 0.5 seconds (as above).

Fault at location 1

There are no interlocking signals. The main breaker trip

unit will initiate the trip in 0.045 seconds.

Figure A.2 presents a Zone Selective Interlocking connec-

tion diagram for a system with two main breakers from

incoming sources and a bus tie breaker. Note that the

blocking diode D1 is needed so that the feeder breakers

can send interlocking signals to both the main and the tie

breakers and prevent the tie breaker from sending an

interlocking signal to itself.

Courtesy of NationalSwitchgear.com

Summary of Contents for Digitrip 220







































Reviews: