background image

Effective 2/2/2001

Page 3

I.L. 70C1037H03

Table 1.1 Protection Types Available for Digitrip Trip Units

Notes: 1. Limited to 1200 Amperes; this is only for UL versions, not for IEC models.

2. Four cause of trip LEDs–L, S, I, G. Making Current Release is indicated by the Instantaneous LED.

3. Requires Ground Alarm/Power Supply Module (see Section 1.6).

4. Additional  setting is marked M1 where:

800-3200A Frame:

M1 = 14 x /n for Plug Amps 200 through 1250A

M1 = 12 x /n for Plug Amps 1600, 2000, 2500A

M1 = 10 x /n for Plug Amps 3000, 3200A

4000-6300A Frame:

M1 = 14 x /n for Plug Amps 2000, 2500A

M1 = 12 x /n for Plug Amps 3200, 4000, 5000A (see Section 2.5)

M1 = 10 x /n for Plug Amps 6300A

            5. ZSI = Zone Selective Interlock 

(See Section 3.4)

Digitrip Trip Unit Type

220

520/520

i

520M/520M

i

520MC/520MC

i

Ampere Range

200A-3200A

200A-6300A

200A-6300A

200A-6300A

RMS Sensing

Yes

Yes

Yes

Yes

Communications

No

No

No

Yes

3

Protection and Coordination

Protection

Ordering Options

Fixed Rating Plug (

I

n)

Overtemperature Trip

LI

Yes

Yes

LSI,LSIG/WLSIG

Yes

Yes

MLSI,MLSIG,

MLSIA/MWLSIG

Yes

Yes

CLSI, CLSIG,

CLSIA/CWLSIG

Yes

Yes

Long

Long Delay Setting

Delay

Long Delay Time I

2

t at 6 x (

I

r)

Protection

Long Delay Thermal Memory

Fixed @ 1 x (

I

n)

Fixed @ 10 seconds

Yes

0.4-1.0 x (

I

n)

2-24 Seconds

Yes

0.4-1.0 x (

I

n)

2-24 Seconds

Yes

0.4-1.0 x (

I

n)

2-24 Seconds

Yes

Short

Short Delay Pick-Up

4

Delay

Short Delay Time  I

2

t at 8 x (

I

r)

Protection

Short Delay Time FLAT

Short Delay Time ZSI

5

No

No

No

No

200-1000% x (

I

r)

100-500 ms

100-500 ms

Yes

200-1000% x (

I

r)

100-500 ms

100-500 ms

Yes

200-1000% x (

I

r)

100-500 ms

100-500 ms

Yes

Instan-

Instantaneous Pick-Up

4

taneous

Off Position

Protection

Making Current Release

200-1000% x (

I

n)

No

Yes

200-1000% x (

I

n)

Yes

Yes

200-1000% x (

I

n)

Yes

Yes

200-1000% x (

I

n)

Yes

Yes

Ground

Ground Fault Option

(Earth)

Ground Fault Alarm

Fault

Ground Fault Pick-Up

Protection

Ground Fault Delay I

2

t at .625 x (

I

n)

Ground Fault Delay Flat

Ground Fault ZSI

5

Ground Fault Memory

No

No

No

No

No

No

No

Yes

No

25-100% x (

I

n)

1

100-500 ms

100-500 ms

Yes

Yes

Yes

Yes

3

25-100% x (

I

n)

1

100-500 ms

100-500 ms

Yes

Yes

Yes

Yes

25-100% x (

I

n)

1

100-500 ms

100-500 ms

Yes

Yes

System Diagnostics

Status/Long Pick-up LED

Cause of Trip LEDs

Yes

No

Yes

Yes

2

Yes

Yes

2

Yes

Yes

2

Remote Ground Trip/Alarm Contacts

No

No

Yes

3

Yes

System Metering

Digital Display

No

No

4 Char. LCD

4 Char. LCD

Courtesy of NationalSwitchgear.com

Summary of Contents for Digitrip 220







































Reviews: