Custom Audio Electronics KUBE 120 User Manual Download Page 33

Page: 33 / 92

5 CONFIGURATION

5.1

Coniguration mode

To enter the coniguration mode and print a SETUP report with the operating parameters of the device, proceed as follows.

While pressing the FEED key, switch on the

device by pressing the ON/OFF key.

Press the FEED key.

The device prints the report with

parameters for printer settings.

Press the FEED key to enter the configuration mode

or press the ON/OFF key to skip setup procedure.

Enter

setup

FEED

ON/OFF

Skip

setup

FEED

PRINTER SETTINGS

PRINTER TYPE .........................................KUBE SCAN 84MM

PRINTING HEAD TYPE .............................SHEC T80

KUBEII SCANNER

SCODE

<code>

rel

1.00

DCODE

<code>

rel

1.00

FCODE

<code>

rel

1.00

UCODE

<code>

rel

1.00

DCODE

<code>

rel

1.00

FEED

ON/OFF

Summary of Contents for KUBE 120





























































































Search results

Summary of Contents for KUBE 120

Reviews:

Related manuals for KUBE 120

Brands by name

Popular brands

Custom Audio Electronics KUBE 120, User Manual

Search results

Summary of Contents for KUBE 120

Reviews:

Related manuals for KUBE 120

Brands by name

Popular brands