background image

SHIPPING LIST

1.

Iced  Tea  Brewer

2.

PB-2  Brew  Basket

3.

Brew  Cone

4.

Paper  Filters

TCT-35 or -35S

WC-3322

WC-3320

GEM - 6

1

1

1

25

Item

Part

Number

Quantity

Supplied

1.

Loosen the four slotted screws and remove the
top cover. Remove the heating tank lid.

2.

Pour water into the heating tank until the water
level is one to two inches below the siphon
tube. Replace the tank lid.

3.

Connect a water line to the inlet valve behind the
machine. Turn on water.

4.

Locate the thermostat. Turn the stem of the thermo-
stat clockwise until it stops.

5.

Plug in the electrical cord to a 120 VAC, 20 Amp,
outlet. Flip the toggle switch, located behind the
machine, to the ON position. At this time the
READY TO BREW light will be off.

6.

Wait about 20-25 minutes for the water to reach
brewing temperature.

7.

Because of the siphon system, proper water level in the heating tank must be established:

a.

Place iced tea dispenser on the brewer, under the empty brew cone.

b.

Press the brew switch.

c.

As soon as you see water flowing, switch off the ON/RESET switch.

d.

The water level in the heating tank is now correct and the machine is ready to brew.

e.

Make sure the READY TO BREW light is on. This indicates the water in the heating tank is at
operating temperature.

8.

The dual timer operation and setting: The Concentrate Knob determines the entire
length of brew cycle, while the Dilution Knob establishes the length of each of the
five (5) cold water cycles within the brew cycle in order to reach the correct hot to
cold water ratio.

a.

The amount of tea concentrate brewed can be adjusted by the timer
knob marked CONCENTRATE. Use one (1) gallon as the standard setting.

b.

The ratio of tea concentrate to cold water can be adjusted by the
timer knob marked DILUTION.

c.

The starting ratio will be one gallon concentrate and two gallons of
dillution. The ratio can be adjusted to obtain the desired brew.

SET-UP INSTRUCTIONS

123

123

123

123

123

12

DUAL INLET VALVE

HEATING TANK

DUAL BREW
TIMER

THERMOSTAT

ON/RESET SW.

BREW SW.

COMPONENTS, TOP VIEW

GAL

CONCENTRATE

.5

2

GAL

DILUTION

3

1

6

2

4

1

4

z

z

z

z

z

z

z

- 1 -

NOTE: These brewers are set at the factory to brew 3 gallons (TCT-35S) or 5 gallons (TCT-35).

Summary of Contents for TCT-35











Reviews: