background image

 

 3 of 28

 

Curtis cabs feature an assembly of parts designed for your vehicle which require adjustment 

and alignment of components to accommodate vehicle variations and provide proper weather 

protection. For accurate installation, proper operation, and years of satisfaction, please read 

and understand the installation and owner

s manual fully prior to installing the cab.

 

 

From all of us at Curtis, we thank you for choosing our product

.

 

HELPFUL HINTS:

 

Refer to parts diagram found in the service parts section of this manual to help identify parts during the assembly process.

 

To assist with the cab installation, leave all fasteners loose for later adjustment unless otherwise specified.

 

Read and understand all instructions before beginning.

 

Apply a silicone sealant to seal any minor gaps that may occur due to vehicle variations.

 

Use caution to avoid damaging the factory installed threaded inserts or weld nuts.  Begin the thread engagement by hand to 

avoid or correct potential cross threading.

 

Make sure the areas where the supplied self

-

adhesive hook Velcro and seals will be applied are clean, dry, and at room 

temperature for best adhesion.

 

Before installing parts with factory installed rubber, make sure the rubber is fully installed onto the parts for proper fit and 

sealing.

 

  driver and passenger.

  Curtis accessory weights are listed in product

  add additional weight to the base vehicle. All

  Curtis Cabs, blades and general accessories

ADDED

WEIGHT

  brochures. Deduct the accessory's total weight

  from the vehicle's rated capacity and never

  exceed the vehicle's rated capacity including

 

Exposure to Carbon Monoxide 

can Cause illness, serious injury or 

death.  

Never operate vehicle if suspicious of Carbon Monox-

ide.  Inspect exhaust system for leaks monthly.  Leaks can 

result from loose connections, corrosion, cracks or other 

damage to the exhaust manifold.  If leaks are found, repair or 
replace exhaust system.  Do not use vehicle until repair or 

replacement is complete.

 

Set of Standard and Metric Sockets 

(3/8” 

Drive)

 

3/8” 

Drive Ratchet with Extension

 

Torque Wrench

 

Set of Standard and Metric Open

-

End Wrenches

 

Set of Standard and Metric Allen Wrenches

 

#2 and #3 Phillips Head Screwdrivers

 

Flat Head Screw Driver

 

Body Clip Removal Tool

 

Pliers

 

Non

-

Marring Pick 

 

(2) Quick Grip Clamps 

 

 Bar clamp (optional)

 

5/16” 

Nut Driver

 

Coolant Drain Pan

 

 

Drill/Driver

 

#2 and #3 Phillips Head Bit

 

Utility Knife

 

Pair of Scissors

 

Shears

 

Grease

 

Silicone Sealant

 

Teflon Tape

 

Tape Measure

 

China Marker or other Non

-

Permanent Marker

 

Snips

 

WARNINGS, TIPS, & REQUIRED TOOLS

 

TOOLS REQUIRED:

 

GENERAL INFORMATION BEFORE YOU START

 

California Health and Safety Proposition 65 Warning: 

This product may contain chemi-

cals known to the state of California to cause cancer and birth defects or other reproductive harm.  

 

Summary of Contents for 1NHWM25SCA





























Reviews: