Curtis Instruments MultiMode 1243 Generation 2 Manual Download Page 61 | Manualshive

Page: 61 / 90

background image

Curtis 1243

GEN

2 Manual

54

4 — INSTALLATION CHECKOUT

switch wiring is correct, turn off the controller, disconnect the battery,
and exchange the motor

’

s

fi

eld connections (

S1

and

S2

) on the control-

ler. The motor should now turn in the proper direction.

The motor should run proportionally faster with increasing throttle.

If not, refer to Section 7.

CAUTION:

The polarity of the

S1

and

S2

connections will affect the operation of the emergency reverse feature.
The forward and reverse switches and the

S1

and

S2

connections must

be con

fi

gured so that the vehicle drives away from the operator when the

emergency reverse button is pressed.

5. Select the Monitor menu, and scroll down to observe the status of the

forward, reverse, interlock, emergency reverse, and mode switches. Cycle
each switch in turn, observing the programmer. The programmer should
display the correct status for each switch.

6. Verify that all options, such as high pedal disable (HPD), static return

to off (SRO), and anti-tiedown are as desired.

7. On walkies, verify that the emergency reverse feature is working correctly

(i.e., press the emergency reverse button, and con

fi

rm that the wheels

turn in the proper direction to drive the vehicle away from the operator).

If you have the optional emergency reverse check wiring, verify the

checking circuit. Apply throttle so that the drive wheel spins. While
continuing to apply throttle, temporarily disconnect one of the emer-
gency reverse wires. The drive wheel should come to a stop and a fault
should be indicated. Be sure to reconnect the emergency reverse wire
after completing this test of the checking circuit.

☞

C A U T I O N

«
...
59
60
61
62
63
...
»

Summary of Contents for MultiMode 1243 Generation 2



























































































Reviews:

No comments

Related manuals for MultiMode 1243 Generation 2

Brand: ABB Pages: 2

Brand: CAME Pages: 12

Brand: CAME Pages: 16

Brand: Ultrak Pages: 41

Brand: Zander Aachen Pages: 10

Brand: BEIER-Electronic Pages: 22

Brand: Gardena Pages: 17

Brand: SAFI Pages: 18

Brand: Badger Meter Pages: 2

Brand: Badger Meter Pages: 48

BadgerTouch HREBT

Brand: Badger Meter Pages: 12

Brand: Badger Meter Pages: 16

Brand: Häfele Pages: 2

Brand: Häfele Pages: 24

Brand: K'Nex Education Pages: 56

Brand: Omnex Pages: 9

Brand: Omegon Pages: 6

Brand: WATERLOO Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands