Curtis Instruments MultiMode 1243 Generation 2 Manual Download Page 87

Page: 87 / 90

Curtis 1243

GEN

2 Manual

A-4

APPENDIX A: EMC & ESD DESIGN CONSIDERATIONS

B-1

APPENDIX B

CURTIS 1311 HANDHELD PROGRAMMER

The Curtis 1311 handheld programmer provides programming, diagnostic,
and test capabilities for the 1243

GEN

2 controller. The power for operating the

programmer is supplied by the host controller via a 4-pin Molex connector.

The programmer includes a 7-line alphanumeric LCD display, rocker-

type keys for navigating through the display and for modifying parameters (+/
-), and three keys that can be used as bookmarks.

The 1311 programmer is easy to use, with self-explanatory functions.

After plugging in the programmer, wait a few seconds for it to boot up and
gather information from the controller.

For experimenting with settings, the programmer can be left plugged in

while the vehicle is driven.

APPENDIX B: 1311 PROGRAMMER

Parameter
Modification Key

(to increase and
decrease values)

LCD Display

(seven lines,
alphanumeric)

Bookmark Keys

(for jumping easily back
and forth between fields)

Navigation Key

(to move around through
the programmer menus)

Fig. B-1

Curtis 1311

handheld programmer.

Summary of Contents for MultiMode 1243 Generation 2



























































































Search results

Summary of Contents for MultiMode 1243 Generation 2

Reviews:

Related manuals for MultiMode 1243 Generation 2

Brands by name

Popular brands

Curtis Instruments MultiMode 1243 Generation 2, Manual

Search results

Summary of Contents for MultiMode 1243 Generation 2

Reviews:

Related manuals for MultiMode 1243 Generation 2

Brands by name

Popular brands