Culligan HE Twin Water Softener Owner'S Manual Download

Page: 32 / 84

01023052

14. Reattach the electrical enclosure cover to the control valve.

a. Align the circuit board in the enclosure with the three support brackets on the control

valve frame. See Figure 24.

b. Push the enclosure onto the control valve, inserting the circuit board edge in the slots

on the control valve frame and the screw on the enclosure with the hole on the cover.

Align slot on frame with edge of

circuit board in the enclosur

Insert screw on enclosure

into holder on control valv

Align slot on frame

with edge of circuit

board in the enclosur

Align slot on frame with edge of

circuit board in the enclosur

Figure 24.

Attaching enclosure cover to control valve.

c. Screw the enclosure on the control.

d. Attach the strain relief fittings to the Aqua-Sensor probe, 2.5 VAC power cord and

wire harnesses from HE Twin control #2 and insert into the enclosure.

e. Connect the 24 Volt power cord to the two 24 VAC terminals on the transformer.

Summary of Contents for HE Twin Water Softener





















































































Search results

Summary of Contents for HE Twin Water Softener

Reviews:

Related manuals for HE Twin Water Softener

Brands by name

Popular brands

Culligan HE Twin Water Softener, Owner'S Manual

Search results

Summary of Contents for HE Twin Water Softener

Reviews:

Related manuals for HE Twin Water Softener

Brands by name

Popular brands