manualshive.com logo in svg

Culligan HE Twin Water Softener, Owner'S Manual

Share
Download
Culligan HE Twin Water Softener Owner'S Manual Download Page 15

11

01023052

Drain Facilities
Choose a nearby drain that can handle the rated drain flow (floor drain, sink or stand pipe). Refer to “Ta-

ble 3. Height of Discharge Above Floor Level Operating” on page 22, for maximum drain line length.

NOTE 

Most codes require an anti-siphon device or air gap.  Observe all local 

plumbing codes and drain restrictions. The system and installation must 

comply with all state and local laws and regulations.

Electrical Facilities
A 10-foot cord and wall mount plug-in transformer are provided. The customer should provide a recepta-

cle, preferably one not controlled by a switch that can be turned off accidentally. Observe local electrical 

codes.

NOTE 

The softener works on 24 Volt/60 Hz electrical power only. Be sure to use the 

included  transformer. Be sure the electrical outlet and transformer are in an 

inside location to protect from moisture. Properly ground to conform with all 

governing codes and ordinances. Observe all local plumbing codes and drain 

restrictions. The system and installation must comply with all state and local 

laws and regulations.

NOTE 

PN 01020620 and PN 01018133 plug-in transformer are rated for indoor 

installations only.  

Summary of Contents for HE Twin Water Softener





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands