Operation Manual
NORM-O-TEMP
®
, Model 111Z
Page 27 of 50
D.
Review Section 1-3 to identify the features of the NORM-O-TEMP
®
unit.
E.
Collect and arrange the following equipment and supplies:
1.
Hyper-hypothermia blanket/pad(s) Listed in Figure 8.
2.
Connecting hose with quick-disconnect Hansen fittings (if applicable).
F.
Mount the NORM-O-TEMP
®
unit on the proper stand (if applicable).
1.
To mount the NORM-O-TEMP
®
unit on IV Pole Stand:
i.
Place the NORM-O-TEMP
®
unit on the equipment pan with the rear of the
unit facing the IV pole. Slide the NORM-O-TEMP
®
unit toward the IV pole
until the rubber bumper touches the pole
ii.
Fasten the NORM-O-TEMP
®
unit by turning the knurled knobs (on the
underside of the equipment pan) clockwise into the threaded holes on the
bottom of the NORM-O-TEMP
®
unit. Hand tighten knurled knobs until snug.
iii.
Fasten the mounting bracket around the lower IV pole near the bumper on
the rear of the NORM-O-TEMP
®
unit with the two stainless steel machine
screws provided.
2.
To mount the NORM-O-TEMP
®
unit on the Low Profile Stand:
i.
Place the NORM-O-TEMP
®
unit on the equipment pan so that the threaded
holes on the bottom of the unit line up with the knurled knobs (on the
underside of the equipment pan).
ii.
Fasten the NORM-O-TEMP
®
unit by turning the knurled knobs clockwise into
the threaded holes on the bottom of the NORM-O-TEMP
®
unit. Hand tighten
knurled knobs until snug.
G.
Slide the lid of the water fill opening and add 340 cc of propylene glycol then gradually
pour approximately 6 quarts (5.7 liters) of distilled water into the reservoir. DO NOT
USE DE-IONIZED WATER OR TAP WATER. Stop pouring when the water reaches the
strainer visible at the bottom of the water fill opening. DO NOT OVERFILL.
H.
Connect the blanket/pad(s) to the NORM-O-TEMP
®
unit by attaching the quick-
disconnect female Hansen socket of the connecting hose to a male outlet Hansen plug
(on the bottom row) of the unit. Attach the male quick-disconnect Hansen plug of the
connecting hose to a female return Hansen socket (on the top row) of the unit. Each
blanket/pad must be connected to one outlet coupling and one return coupling of the
connecting hose if necessary.
1.
To attach the Hansen fittings:
i.
Grasp the quick-disconnect female Hansen socket of the connecting hose
ii.
Slide the collar back towards the hose
iii.
Push the female Hansen socket of the hose over a male Hansen plug of the unit
iv.
Allow the collar to SNAP into place and return to its original position
v.
Gently pull on the connecting hose to assure a positive connection
vi.
Next, push back the collar of a female Hansen socket on the unit with one hand
vii.
With the other hand, insert the male Hansen plug of the connecting hose
viii.
Release the collar of the female Hansen socket
ix.
Push the male Hansen plug until it SNAPS into position
x.
Gently pull the connecting hose to assure a positive connection
Summary of Contents for Norm-o-Temp 111Z
Page 13: ...Operation Manual NORM O TEMP Model 111Z Page 13 of 50 Figure 1 NORM O TEMP unit Front View...
Page 15: ...Operation Manual NORM O TEMP Model 111Z Page 15 of 50 Figure 2 NORM O TEMP unit Left Side View...
Page 17: ...Operation Manual NORM O TEMP Model 111Z Page 17 of 50 Figure 3 NORM O TEMP unit Rear View...
Page 49: ...NORM O TEMP Model 111Z Page 49 of 50 THIS PAGE INTENTIONALLY LEFT BLANK...
