background image

6

MAB 465

GB

Danger from electric current!

 DANGER

Danger to life from electrical current!
Contact with live wires or components 

can lead to serious injury or even 

death!

Observe the following safety precautions 

to avoid any danger from electric current:

 

Do not open the housing of the 

machine. Risk of electric shock from 

touching live connections.

 

Never immerse the machine or mains 

plug in water or other liquids.

 

Only use extension cables or cable 

drums with a cable cross-section of at 

least 1.5 mm².

 

Only use extension cables that are 

approved for the location of use.

 

Check the condition of the extension 

cable regularly and replace if dam-

aged.

 

Avoid bodily contact with grounded 

parts (e.g., pipes, radiators, steel 

girders) to reduce the risk of electric 

shock in the event of a defect.

 

When using the machine outside or in 

a humid environment, an RCD (resid-

ual circuit device) must be used.

Risk of injury!

 WARNING

Risk of injury from engine starting 

unintentionally!

Pay attention to the following safety 

notes to avoid danger from motor starting 

unintentionally:
For safe stopping of the motor:

 

Press the red button (O) of the motor 

switch (21).

 

Switch off the machine with the ON/

OFF switch (main switch) (23).

 

Disconnect the voltage supply (pull 

out the mains plug).

 WARNING

Improper handling of the machine 

increases the risk of injury!

Pay attention to the following safety 

instructions in order not to injure others 

or yourself:

 

Operate the machine only with the 

protective equipment specified in 

these instructions (see section 

“Per-

sonal protective equipment”

).

 

Do not

 wear protective gloves when 

the machine is running. A glove can 

be caught by the drilling machine and 

torn off the hand. Risk of losing one 

or more fingers.

 

Remove loose jewellery before begin-

ning work.

 

Wear a hair net if you have long hair.

Safety

WWW.CSUNITEC.COM

Summary of Contents for MAB 465























Reviews: