background image

Elegant 

CRYSTAL QUEST

®

 Elegant Floor Water Cooler

Hybrid 

CRYSTAL QUEST

®

 Hybrid Floor Water Cooler

Floor Hybrid

ELEGANT / HYBRID

SYSTEM SPECIFICATIONS

ELEGANT / HYBRID

SYSTEM SPECIFICATIONS

Elegant Floor

with Wheels

Elegant 

Floor

Weight: 60 lbs. . 
Dimensions: 
(D) 17.6” x (W) 14.4” x (H) 42”  
Total reservoir capacity: 1.5 Gal
Hot water tank temperature: 185°F 
Heating power: 500W 6.2 Amps
Cooling power: 112W 2.4 Amps
Hot water tank volume: 0.5 gal
Cold water tank volume: 0.4 gal 
Cooling capacity: 1 gal per hour
Voltage: 110V-120V 50/60Hz

CRYSTAL QUEST

®

 Hybrid Floor 

Water Cooler

Setting Temperatures and Dispensing Water

Set the heating and cooling temperatures.  Press the setup button on the front until the LCD display changes to the 

1. 

temperature set screen, then you may adjust the temperature for each to your desired level by pressing the hot/+ 

to raise the value and the cold/- to lower the value.  Default values are: hot water 95°C, and cold water 8°C.  When 

finished setting values, the unit will automatically go to normal operation after several seconds of no buttons being 

pushed.

Turn on the heating and cooling.  To do this press the hot/+ button once to turn on heater, press the cold/- button to 

2. 

turn on cooling.

Water dispensing: To dispense hot water, press the silver unlock button then press the silver hot button. You will 

3. 

hear a beep and hot water will dispense from the left spout.  Caution: The default temperature of the hot water will 

scald the skin.  Press the silver hot button again and the hot dispensing will stop.  To dispense cold water, press 

the silver cold button. The system will beep and cold water will dispense from the right spout.  Press the silver cold 

button again and the cold dispensing will stop.

Accessing Internal parts

Turn off heating and cooling switches.

1. 

Shut off water supply to the system.

2. 

Drain water from drain ports on the back of system and unplug power cord.

3. 

Remove two screws attaching top to back of system.

4. 

Remove top of system and the top of holding reservoir.

5. 

Remove screws attaching back of system to the cabinet and remove holding reservoir.

6. 

Access is now available for most of the internal parts of the system for repair or replacement.

7. 

“Cold” Indicator Light

“Heating” Indicator Light

“Hot” Indicator Light

Hot Water Faucet
Cold Water Faucet

Filtration Access Door

Filtration System

Water Inlet

Cold Control

Cold Water 

Drain

Hot Water 

Drain

Wire to 

Electrical Outlet

Cold On/Off 

Switch

Hot On/Off 

Switch

On/Off Switch

Handle

Water Inlet

Hot Water Drain

Cold Water Drain
Tank Water Drain
Cartridges Water Drain

Wire to Electrical 

Outlet

Display Screen

On/Off Switch

Temperature Adjuster

Cold Water Faucet

Cold Water Temperature

Control

Hot Water 

Safety Button

Filtration Access

Door

Hot Water Button
Hot Water Faucet

Filtration System

Hot Water 

Temperature Control

CRYSTAL QUEST

®

 Elegant Floor 

Water Cooler

Weight: 60 lbs. . 
Dimensions: 
(D) 14.5” x (W) 14 3/4” x (H) 39.25”  
Total reservoir capacity: 3.2 Gal
Hot water tank temperature: 185°F 
Heating power: 500W 6.2 Amps
Cooling power: 112W 2.4 Amps
Hot water tank volume: 0.5 gal
Cold water tank volume: 1.2 gal 
Cooling capacity: 1.95 gal per hour
Voltage: 110V-120V 50/60Hz

4

Summary of Contents for Elegant

















Reviews: