background image

Do not lay the cooler on its side.The system must be in an upright position at all times. When carrying, do not lift the system by the faucets/

• 

spouts.

The system needs to be installed by a licensed plumber in any state or country; however, the following states specifically require a licensed 

• 

plumber to install the system OR allow a state-registered installer or contractor:  AR, CA, GA, KS, MA, MI, MN, OK, RI, SC, SD, TX, VT, and 

WI.

A pressure regulator, such as a slow-flow regulator, must be installed in front of the unit’s water inlet if the water pressure (including any 

• 

possible pressure spikes) could exceed 60 psig. Failure to comply will void the warranty. Crystal Quest

®

 accepts no liability for damage 

caused by excessive water pressure or improper installation.

Installation must be made within a protected area covered from the elements and freezing. The unit must be protected from rain, dust,  

• 

flooding, snow, freezing, and direct sunlight (the system’s direct exposure to sunlight may cause algae growth in the tank reservoir). Failure 

to comply will void the warranty.

Use only ¼” OD tubing to connect the cold water supply to the system.

• 

Check all the connections (i.e., water hose/tubing, connectors/fittings) to ensure proper connection and avoid leaks.

• 

Check plumbing inlet and outlet to ensure the proper flow of water through the system.

• 

Plug the system into a 110 volt grounded outlet which contains a fuse or circuit breaker of 20 amps.

• 

Locate the system near a cold water supply line. Do not set the system farther than 15 ft. from the cold water line. Use copper tubing to 

• 

avoid water line puncture and rodent bites. Failure to do so may cause major property damage. Crystal Quest

®

 accepts no liability for   

damage.

Install the system in a well-ventilated area where the temperature is consistently above 60ºF.

• 

System must have a 2” clearance on all sides to ensure proper ventilation.

• 

Install the auto shut-off valve to control and reduce the cold water supply line pressure to 25 psi and maintain at 25 psi to avoid bursting.

• 

Hot water tank must be filled with water before the heating on/off switch is turned on.

• 

Do not use the system on cold water supply line with less than 20 psi.

• 

Do not move the cooler if filled with water.

• 

Important Information  .........................................................................................................................................................................2

System Specifications (Turbo/Sharp)

 ..................................................................................................................................................3

System Specifications (Elegant/Hybrid)

 ..............................................................................................................................................4 

Installation Instructions ................................... ....................................................................................................................................5
Circuit and Installation Diagrams  ........................................................................................................................................................6
Install Water Cooler System to Water Supply ......................................................................................................................................7
Service Information and Guidelines .....................................................................................................................................................8
Replacement Cartridges ......................................................................................................................................................................9
Troubleshooting Guide (Water Problems) ...........................................................................................................................................10
Troubleshooting Guide (Unit Problems) ..............................................................................................................................................11
Access to Parts Inside the System ......................................................................................................................................................12
Water Cooler Heating Reservoir Replacement Guide .........................................................................................................................13
Water Coolers (Optional Cartridges & Accessories) ............................................................................................................................14
System Warranty .................................................................................................................................................................................15
Ordering Replacement Cartridges .......................................................................................................................................................16

Important Information

Table of Contents

2

Summary of Contents for Elegant

















Reviews: