Crusader CWS5-031 Owner'S Manual Download Page 8 | Manualshive

Page: 8 / 26

Crusader CWS5-031 Owner'S Manual Download Page 8

8 |

P a g e

Step 5:

It is strongly recommended to have a licensed plumber connect the UV reactor to the

water supply and may be a requirement depending on where you are located. If you are attempting
this yourself, ensure you have all the necessary tools and fittings to accomplish this task.

Step 6:

Although there are many methods of installation, this manual will provide a

recommended  procedure  using  copper  plumbing  and  standard  soldering  methods.  Crusader
recommends  the  use  of  unions,  a  by-pass  assembly  and  shut-off  valves  as  this  will  allow  you  to
isolate  and  remove  the  UV  reactor  if  necessary  (this  method  is  a  recommended  method  only
however it allows for the maximum convenience but it requires extra components and more time
for installation. Please refer to Figure 3 for the recommended installation.

Figure 2. Recommended POE Installation

Figure 3. Recommended Installation

«
...
6
7
8
9
10
...
»

Summary of Contents for CWS5-031



























Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands