background image

Limited Warranty

We warrant to our immediate customer and to the ultimate consumer that products of our manufacture will be free of defects
in material and workmanship under normal use and service for the following time periods, when installed and maintained in
accordance with our instructions. 
Pump Products: One (1) year from date of installation or (24) twenty-four months from date of shipment, whichever occurs
first. Cleaning Products: Twelve (12) months from date of installation or eighteen (18) months from date of shipment, whichever
occurs first. As used herein, "the ultimate consumer" is defined as the purchaser who first uses the product after its initial
installation or, in the case of product designed for non permanent installation, the first owner who used the product. It is the
purchaser’s or any sub-vendee’s obligation to make known to the ultimate consumer the terms and conditions of this warranty.
This warranty gives you specific legal rights, and there may also be other rights which vary from state to state. In the event
the product is covered by the Federal Consumer Product Warranties Law (1) the duration of any implied warranties associated
with the product by virtue of said law is limited to the same duration as stated herein, (2) this warranty is a LIMITED
WARRANTY, and (3) no claims of any nature whatsoever shall be made against us, until the ultimate consumer, his successor,
or assigns, notifies us in writing of the defect, and delivers the product and/or defective part(s) freight prepaid to our factory
or nearest authorized service station. Some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply. 

THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF ANY AND ALL WARRANTIES WITH

RESPECT TO ANY PRODUCT SHALL BE TO REPLACE OR REPAIR AT OUR ELECTION, F.O.B. POINT OF
MANUFACTURE OR AUTHORIZED REPAIR STATION, SUCH PRODUCTS AND/OR PARTS AS PROVEN DEFECTIVE.
THERE SHALL BE NO FURTHER LIABILITY, WHETHER BASED ON WARRANTY, NEGLIGENCE OR OTHERWISE.

Unless expressly stated otherwise, guarantees in the nature of performance specifications furnished in addition to the foregoing
material and workmanship warranties on a product manufactured by us, if any, are subject to laboratory tests corrected for
field performance. Any additional guarantees, in the nature of performance specifications must be in writing and such writing
must be signed by our authorized representative. Due to inaccuracies in field testing if a conflict arises between the results of
field testing conducted by or for user, and laboratory tests corrected for field performance, the latter shall control. Components
or accessories supplied by us but manufactured by others are warranted only to the extent of and by the terms and conditions
of the original manufacturer’s warranty. 

RECOMMENDATIONS FOR SPECIAL APPLICATIONS OR THOSE RESULTING

FROM SYSTEMS ANALYSES AND EVALUATIONS WE CONDUCT WILL BE BASED ON OUR BEST AVAILABLE
EXPERIENCE AND PUBLISHED INDUSTRY INFORMATION. SUCH RECOMMENDATIONS DO NOT CONSTITUTE A
WARRANTY OF SATISFACTORY PERFORMANCE AND NO SUCH WARRANTY IS GIVEN.

This warranty shall not apply when damage is caused by (a) improper installation, (b) improper voltage (c) lightning (d) sand
or other abrasive material (e) scale or corrosion build-up due to excessive chemical content. Any modification of the original
equipment will also void the warranty. We will not be responsible for loss, damage or labor cost due to interruption of service
caused by defective parts. Neither will we accept charges incurred by others without our prior written approval.
This warranty is void if our inspection reveals the product was used in a manner inconsistent with normal industry practice
and\or our specific recommendations. The purchaser is responsible for communication of all necessary information regarding
the application and use of the product. 

UNDER NO CIRCUMSTANCES WILL WE BE RESPONSIBLE FOR ANY OTHER

DIRECT OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED

 

TO LOST PROFITS, LOST INCOME, LABOR

CHARGES, DELAYS IN PRODUCTION, IDLE PRODUCTION, WHICH DAMAGES ARE CAUSED BY ANY DEFECTS IN
MATERIAL AND\OR WORKMANSHIP AND\OR DAMAGE OR DELAYS IN SHIPMENT. THIS WARRANTY IS EXPRESSLY
IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTY, INCLUDING ANY WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE.

No rights extended under this warranty shall be assigned to any other person, whether by operation of law or otherwise, without
our prior written approval.

420 Third Street/P.O. Box 603

83 West Drive, Brampton

Piqua, Ohio 45356-0603

Ontario, Canada L6T  2J6

Phone: (937) 778-8947

Phone: (905) 457-6223

Fax: (937) 773-7157

Fax: (905) 457-2650

www.cranepumps.com

PUMPS & SYSTEMS

A Crane Co. Company

Summary of Contents for CT4QP Series



























Reviews: