background image

15

WARRANTY TERMS

 

CRISTÓFOLI EQUIPAMENTOS DE BIOSSEGURANÇA

 warranties the Cristófoli Vacuum Pumps 

for 01 (one) year against any manufacturing defect from the date of the purchase receipt 
(provided it contains the serial and lot numbers of the equipment), of which 03 (three) months 
refer to the legal warranty (established by section II, art. 26, CDC, Brasil) and nine (09) months to 
the contractual warranty (arranged in art. 50, CDC, Brazil). Visit our website www.cristofoli.com 
and register your product online.

 

Traveling  costs  (based  on  the  distance  traveled  in  km)  and  the  stay  of  the  authorized 

technician for installation, repair or maintenance 

before or after the warranty period

 will be 

responsibility  of  the  buyer/owner  as  well  as  the  costs  related  to  the  autoclave  sterilization 
monitoring (tests with biological indicators) and freight charges for shipping the equipment to 
the authorized technical assistance office for repairs or, if necessary, to the factory itself.

 

The warranty will be voided in cases of:

 

 Problems arising from natural causes (such as floods, lightning, etc.);

 

 Sinister (theft or robbery);

 

 Damage caused by accidents, such as: dents, drops, short circuits, fire, etc.;

 

 Problems due to failure of the power supply and/or building wiring;

 

 Improper use / installation of the equipment and/or plugging it into an incorrect voltage 

outlet;

 

 Removal and/or tampering of the serial number shown in the identification label of the 

product;

 

 Signs of tampering and/or blotted out data on the purchase or service receipt of the 

equipment;

 

 Signs of external violation of the product or broken factory seal;

 

 Use of non-original or not acquired at the 

CRISTÓFOLI

 Authorized Service Network parts;

 

 Alteration in the equipment performed by the client.

 

 Repairs performed by technicians who are not part of the 

CRISTÓFOLI

 Authorized Service 

Network; 

 

 Noncompliance with any measure or caution recommended in the instruction manual of 

the product.

 

Fuse and filtering element are not covered by warranty.

ATTENTION!

  In order to validate the contractual warranty of the product it is necessary to send a copy of 
the purchase receipt to the following e-mail address: [email protected].

C R I S T Ó F O L I

V A C U U M  P U M P S

I N S T R U C T I O N 

M A N U A L 

Summary of Contents for SuperGap Evolution 2

















Reviews: