background image

 

23 

PROGRAMMABLE OPTIONS Cont. 

 
12. DOOR LOCK/UNLOCK PULSE TIME: 

This option controls the amount of time (0.75 sec. or 3 sec.) for the lock/unlock pulse.  The standard pulse time for 
most  vehicles  is  0.75  Sec.    The  3  sec.  setting  may  be  required  for  Mid  1980’s  through  Mid  1990’s  European 
Vehicles that require a long lock and unlock pulse to operate Vacuum door lock systems. 

 

13. DOUBLE UNLOCK PULSE: 

With this option ON, the unit will send 2 unlock pulses when the system is disarmed.  This feature may be required 
for interfacing a Factory alarm or keyless entry system. 

 
14. LOCK DURING/AFTER REMOTE START: 

This option controls whether the unit will automatically lock during and after a remote Start abort or time-out. 

 

15. NO OPTION / NOT USED 

 

16. TIMED CRANK or TACH MONITOR MODE:

 

This option controls whether the system uses a tach wire to control the starter or uses a pre-set cranking time. 

 

17. BLUE/BLACK WIRE PROGRAMMING: (NEG.) IGNITION OUTPUT or AUX #2 OUTPUT:

 

This option controls the function of the Blue/Black wire as either a Ground with Remote Start or a 2

nd

 Aux. Channel 

 

18. SIREN CHIRPS WITH ARM/DISARM: 

With  this  feature,  siren  chirps  with  Arm/Disarm  can  be  programmed  either  ON  or  OFF  when  using  the  regular 
Lock/Unlock Buttons.  When chirp are OFF, the Flashing parking lights will be the only Arm/Disarm confirmation. 

 

19. +12V “WAKE UP” PULSE: 

This  option  allows  the  unit  to  provide  a  1-second  pulse  on  the  Pink  main  ignition  output  when  unlocking.    The 
Ignition  pulse  serves  to  “Wake  up”  vehicle  control  modules  or  body  computers  that  “time  out”  or  go  into  power 
saving  mode.  This  is  required  on  many  late  model  Ford  vehicles  with  a  “Slam”  lock  system  in  order  to  actually 
unlock the vehicle after it has been at rest for a short period of time.

 

 

20. PINK WIRE PROGRAMMING:  CAR JACK TRIGGER or GLOW PLUG INPUT: 

This option controls whether the system’s PINK input wire functions as a Glow Plug input wire for Diesel Engines or 
a +12V input for tripping a Carjack countdown.  For Glow plug, this wire should be connected to the wait to start light 
circuit and for Carjack this wire can be connected to a hidden button, switch, or a (+) Positive door pin circuit. 

 

 

Summary of Contents for CS-2011

































Reviews: