CrimeStopper CS-2011 Installation Handbook Download | Manualshive

Page: 26 / 32

background image

26

REMOTE PROGRAMMING DIAGRAM

1.  Turn key to the ON position.( doors will lock if autolock is programmed )
2.  Press Programming button 4 times, then after a few seconds the unit will flash the parking lights 4 times.
3.  For  CS2011DP  systems:  Press  button  #1  (Lock)  of  the  transmitter;  for  2-Way  paging  systems  and  “Sidekick”  remotes:

Press Buttons #1 & 2 together. You should get 2 light flashes indication the unit is waiting for a 2

nd

code, then press the

same combination of buttons on a second remote, the unit will flash 3 times indicating its waiting for the 3

rd

code and lights

will flash 4 times for 4

th

code. If all 4 codes are learned, the unit will automatically exit code-learning mode, otherwise turn

key off and close hood.

NOTE: When learning 2-Way LCD or 2-Way LED remotes, wait for the confirmation beep or LCD “Antenna Icon” message
before learning the next remote.

IGN

OFF

WAIT FOR

4 FLASHES

PRESS 4X's

FLASH 2, 3, or 4 X's

2-WAY SYSTEMS &

ONE WAY CS-2011DP

IGN

OFF

PRESS TOGETHER

LOCK &

UNLOCK

PRESS

LOCK ONLY

"SideKick" REMOTES

COMPLETE

«
...
24
25
26
27
28
...
»

Summary of Contents for CS-2011

































Reviews:

No comments

Related manuals for CS-2011

Brand: S Fire Pages: 2

Brand: Deling Electron Pages: 4

Ei 3105TYCH Optical

Brand: Ei Electronics Pages: 2

Brand: Uniel Pages: 20

Brand: Metasys Pages: 16

Car Security System APS-610

Brand: Audiovox Pages: 10

Brand: Audiovox Pages: 11

Brand: Audiovox Pages: 20

Brand: Xtralis Pages: 40

Brand: Marmitek Pages: 44

Brand: CrimeStopper Pages: 1

Brand: HumanTechnik Pages: 40

Brand: La Crosse Technology Pages: 5

Brand: Oregon Scientific Pages: 2

Brand: Eurotops Pages: 15

2000 Pro Series

Brand: Ultra Start Pages: 2

Brand: Ultra Start Pages: 8

Brand: Hama Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands