CrimeStopper CS-2011 Installation Handbook Download

Page: 2 / 32

TABLE OF CONTENTS

Pre-Installation Considerations…………………...….…...…………...……………………………………………………….2

Cautions & Warnings…….…………………………..…..………………………………………………………………………3

Component Mounting………….……………………..……………………………………………….…………………..……..3

Wiring Information ………….…………………………....……………...……………………………………………..……4-12

Power Door Lock Wiring, Systems & Diagrams..….………………...….………..…….……..…………...……………13-15

Tachless, Tach Reference, Tach Finder, Timed Crank Modes………..……………………………………………....16-18

Diesel Glow Plug Delay………………………………………………………………………………………………...………19

Programmable Options, Options Reset……….………………………………………………….………….………...…19-25

Remote Transmitter / Transceiver Programming (1-Way & 2-Way Remotes)……..…………………...…...…...….25-26

2-Vehicle Operation……………………………………………………………………………………………………...……..27

Alarm Trigger Diagnostics…………………....…………………………………………………………………….………….28

Remote Start Diagnostics………….……………………..………………………………………...…………………...…….28

Jumper Pin Diagram…………………………………………………………………………………………………………....29

Antenna Diagram, System Wiring Diagram, DATA Port Diagram..……………………………………………………30-32

PRE-INSTALLATION CONSIDERATIONS

BEFORE BEGINNING

, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS

BRAKES, ENGINE / BODY COMPUTER AND BATTERY).

PLAN OUT YOUR INSTALLATION

. You should pre-determine the location of the Control Module (Brain), Valet button,

LED, and Siren locations. This will save time and ease the installation process.

USE VOLT/OHM METER

to test and locate all connections. Test Lights or Lighted Probes could possibly damage a

vehicle’s computer system or cause an airbag to deploy.

ADDITIONAL PARTS

, that are not included with this unit, may be needed for your particular vehicle. These items may

include extra relays, Door Lock Interface Modules, or Transponder Override modules.

Summary of Contents for CS-2011

































Search results

Summary of Contents for CS-2011

Reviews:

Related manuals for CS-2011

Brands by name

Popular brands

CrimeStopper CS-2011, Installation Handbook

Search results

Summary of Contents for CS-2011

Reviews:

Related manuals for CS-2011

Brands by name

Popular brands