Creotech CTI-PS6 User Manual Download Page 13 | Manualshive

Page: 13 / 31

Creotech CTI-PS6 User Manual Download Page 13

13

Creotech Instruments S.A.

tel. +48 22 233 10 27

ul. Gen. L. Okulickiego 7/9

e-mail: [email protected]

05-500 Piaseczno, Polska www.creotech.pl

2.6.1.3

Configuration of the IP Power Strip Ethernet link

After successful logging in, select Configuration tab and then from the menu on the left, select a
Network group.

Change the following parameters to comply with the requirements of the target Ethernet network
the IP Power Strip is intended to be used in. Static IP configuration can be used (preferable) or a
DHCP:

- IP Address (static), Subnet mask, Default Gateway.

- Enable Configure using DHCP option for DHCP configuration.

Double-check the new configuration settings.

After all the changes were made correctly press Save Network Configuration.

You will be asked to confirm the changes.

After pressing OK the device will countdown 10 seconds during which the device will reset and the
new settings will take effect.

Verify the configuration (it might be useful to check the MAC address of the IP Power Strip for easier

identification of the assigned IP address when DHCP is used).

«
...
11
12
13
14
15
...
»

Summary of Contents for CTI-PS6
































Reviews:

No comments