Cray CX1000 Site Preparation Manual Download

Page: 9 / 56

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to correct the interference

at their own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC

emission limits. Neither the provider nor the manufacturer are responsible for any radio or

television interference caused by using other than recommended cables and connectors or by

unauthorized changes or modifications to this equipment. Unauthorized changes or

modifications could void the user's authority to operate the equipment.

Pursuant to Part 15.21 of the FCC Rules, any changes or modifications to this equipment not

expressly approved by Cray, Inc may cause harmful interference and void the FCC

authorization to operate this equipment.
An FCC regulatory label is affixed to the equipment.

Canadian Compliance Statement (Industry Canada)

This Class A digital apparatus meets all requirements of the Canadian Interference Causing

Equipment Regulations.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
This product is in conformity with the protection requirements of the following standards:

•

ICES-003

•

NMB-003

Laser Compliance Notice (if applicable)

This product that uses laser technology complies with Class 1 laser requirements.
A CLASS 1 LASER PRODUCT label is affixed to the laser device.

Legal Information

Class  1  Laser Product
Luokan 1  Laserlaite
Klasse  1  Laser Apparat
Laser Klasse  1

Summary of Contents for CX1000

























































Search results

Summary of Contents for CX1000

Reviews:

Related manuals for CX1000

Brands by name

Popular brands

Cray CX1000, Site Preparation Manual

Search results

Summary of Contents for CX1000

Reviews:

Related manuals for CX1000

Brands by name

Popular brands