background image

Submersible Pumps

Resistance of cable and pump motor (measured at pump control):
Red-Black:_______Ohms(

Ω

)      Red-White:_______Ohms(

Ω

)     White-Black:_______Ohms(

Ω

)

Resistance of Ground Circuit between Control Panel and outside of pump: __________Ohms(

Ω

)

MEG Ohms check of insulation:
Red to Ground:  _________  White to Ground:  __________   Black to Ground: ____________

Operational Checks

Is there noise or vibration present?   YES___   NO___  Source of noise/vibration: ___________
Does check valve operate properly?   YES___   NO___   N/A___
Is system free of leaks?   YES___   NO___    

Leaks at: ______________________________

Does system appear to operate at design fl ow rate?   YES___   NO___
Nominal Voltage: _____________________ Phase:     1Ø     3Ø     (select one)
Voltage Reading at panel connection, Pump OFF: L1, L2  _____   L2, L3  ____   L1, L3 _____
Voltage Reading at panel connection, Pump ON: L1, L2  ______  L2, L3  ____   L1, L3 _____
Amperage Draw, Pump ON:   L1 ____________  

L2  _____________  

L3  _____________

Submersible Pumps

Are BAF and guide rails level / plumb?   YES___   NO___
Is pump seated on discharge properly?   YES___   NO___
Are level controls installed away from turbulence?   YES___   NO___
Is level control operating properly?   YES___   NO___ 

 

Is pump fully submerged during operation?   YES___   NO___

Follow up/Corrective Action Required

YES___          NO___

Additional Comments:

____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________

Startup performed by: _____________________   Date: ______________________________

Present at Start-Up

(  ) Engineer: ____________________________   (  ) Operator: ________________________

(  ) Contactor: ____________________________   (  ) Other: ___________________________

All parties should retain a copy of this report for future trouble shooting/reference

A Crane Co. Company

420 Third Street 

83 West Drive, Brampton

Piqua, Ohio 45356 

Ontario, Canada L6T 2J6

Phone: (937) 778-8947 

Phone: (905) 457-6223

Fax: (937) 773-7157 

Fax: (905) 457-2650

www.cranepumps.com

Summary of Contents for Crown B12 Series

































Reviews: