background image

3

SAFETY INSTRUCTIONS

TRAINING

• 

Read, understand, and follow all instructions on the machine and in the 
manual(s) before attempting to assemble and operate. Failure to do so can 
result in serious injury to the operator and/or bystanders. Keep this manual 
in a safe place for future and regular reference and for ordering replacement 
parts. 

• 

Be familiar with all controls and their proper operation. Know how to stop 
the machine and disengage them quickly.

• 

Never allow children under 14 years of age to operate this machine. Children 
14 and over should read and understand the instructions and safe operation 
practices in this manual and on the machine and be trained and supervised 
by an adult. 

• 

Never allow adults to operate this machine without proper instruction. 

• 

Thrown objects can cause serious personal injury. Plan your snow-throwing 
pattern to avoid discharge of material toward roads, bystanders and the like. 

• 

Keep bystanders, pets and children at least 75 feet from the machine while it 
is in operation. Stop machine if anyone enters the area.

• 

Exercise caution to avoid slipping or falling, especially when operating in 
reverse.

PREPARATION

• 

Thoroughly inspect the area where the equipment is to be used. Remove all 
doormats, newspapers, sleds, boards, wires and other foreign objects, which 
could be tripped over or thrown by the auger/impeller. 

• 

Always wear safety glasses or eye shields during operation and while 
performing an adjustment or repair to protect your eyes. Thrown objects 
which ricochet can cause serious injury to the eyes.

• 

Do not operate without wearing adequate winter outer garments. Do not 
wear jewelry, long scarves or other loose clothing, which could become 
entangled in moving parts. Wear footwear which will improve footing on 
slippery surfaces. 

• 

Use a grounded three-wire extension cord and receptacle for all machines 
with electric start engines. 

• 

Disengage all control levers before starting the engine. 

• 

Adjust collector housing height to clear gravel or crushed rock surfaces.

• 

Never attempt to make any adjustments while engine is running, except 
where specifically recommended in the operator’s manual.

• 

Let engine and machine adjust to outdoor temperature before starting to 
clear snow. 

Safe Handling of Gasoline:

To avoid personal injury or property damage use extreme care in handling 
gasoline. Gasoline is extremely flammable and the vapors are explosive. 
Serious personal injury can occur when gasoline is spilled on yourself or your 
clothes which can ignite.  Wash your skin and change clothes immediately.

• 

Use only an approved gasoline container.

• 

Never fill containers inside a vehicle or on a truck or trailer bed with a plastic 
liner. Always place containers on the ground away from your vehicle before 
filling.

• 

When practical, remove gas-powered equipment from the truck or 
trailer and refuel it on the ground. If this is not possible, then refuel such 
equipment on a trailer with a portable container, rather than from a gasoline 
dispenser nozzle.

• 

Keep the nozzle in contact with the rim of the fuel tank or container opening 
at all times until fueling is complete. Do not use a nozzle lock-open device.

• 

Extinguish all cigarettes, cigars, pipes and other sources of ignition.

• 

Never fuel machine indoors.

• 

Never remove gas cap or add fuel while the engine is hot or running. Allow 
engine to cool at least two minutes before refueling.

• 

Never over fill fuel tank. Fill tank to no more than ½ inch below bottom of 
filler neck to allow space for fuel expansion.

• 

Replace gasoline cap and tighten securely.

• 

If gasoline is spilled, wipe it off the engine and equipment. Move unit to 
another area. Wait 5 minutes before starting the engine. 

 WARNING

This symbol points out important safety instructions which, if not 
followed, could endanger the personal safety and/or property of 
yourself and others. Read and follow all instructions in this manual 
before attempting to operate this machine. Failure to comply with these 
instructions may result in personal injury. When you see this symbol, HEED 
ITS WARNING!

 WARNING

CALIFORNIA PROPOSITION 65

Engine Exhaust, some of its constituents, and certain vehicle components 
contain or emit chemicals known to State of California to cause cancer and 
birth defects or other reproductive harm.

 DANGER

This machine was built to be operated according to the safe operation 
practices in this manual. As with any type of power equipment, 
carelessness or error on the part of the operator can result in serious injury. 
This machine is capable of amputating fingers, hands, toes and feet and 
throwing debris. Failure to observe the following safety instructions could 
result in serious injury or death.

 WARNING

Your Responsibility

—Restrict the use of this power machine to 

persons who read, understand and follow the warnings and instructions in 
this manual and on the machine. 

SAVE THESE INSTRUCTIONS!

Summary of Contents for 247.881980

























Reviews: