background image

5

SAFETY INSTRUCTIONS

• 

Check fuel line, tank, cap, and fittings frequently for cracks or leaks. Replace 
if necessary.

• 

Do not crank engine with spark plug removed.

• 

According to the Consumer Products Safety Commission (CPSC) and the 
U.S. Environmental Protection Agency (EPA), this product has an 

Average 

Useful Life

 of seven (7) years, or 60 hours of operation. At the end of 

the 

Average Useful Life

 have the machine inspected annually by an 

authorized service dealer to ensure that all mechanical and safety systems 
are working properly and not worn excessively. Failure to do so can result in 
accidents, injuries or death.

DO NOT MODIFY ENGINE

To avoid serious injury or death, do not modify engine in any way. Tampering 
with the governor setting can lead to a runaway engine and cause it to 
operate at unsafe speeds. Never tamper with factory setting of engine 
governor.

NOTICE REGARDING EMISSIONS

Engines which are certified to comply with California and federal EPA 
emission regulations for SORE (Small Off Road Equipment) are certified 
to operate on regular unleaded gasoline, and may include the following 
emission control systems: Engine Modification (EM), Oxidizing Catalyst (OC), 
Secondary Air Injection (SAI) and Three Way Catalyst (TWC) if so equipped.

Summary of Contents for 247.881980

























Reviews: