manualshive.com logo in svg

Craftsman 247.881980, Operator'S Manual

Share
Download
Craftsman 247.881980 Operator'S Manual Download Page 19

19

MAINTENANCE & SERVICE

Auger Belt

IMPORTANT: 

Because gas could leak from the carburetor when servicing auger belt, 

run the engine until the fuel tank is empty as instructed in Replacing Belts.
1. 

Tip the snow thrower up and forward so that it rests on the auger housing.  
Remove the belt keeper as called out in Figure 20. Return the snow thrower 
to its upright position to complete the following steps.

2. 

Slip the front auger belt off of the engine pulley, pushing it forward and 
rolling in off of the pulley. See Figure 19.

Drive 
Belt

Engine 
Pulley

Auger Belt

Auger 
Pulley

Idler Bracket

Belt Keeper

Figure 19

3. 

Squeeze the auger control to release the auger brake, which is the tab that 
holds the belt onto the auger pulley. Remove the belt.

4. 

If the drive belt is also being replaced proceed to Drive Belt instructions.

5. 

If the drive belt is not being replaced, install new auger belt and re-install 
belt cover and belt keeper shown in Figure 20.

Drive Belt

IMPORTANT: 

Because gas could leak from the carburetor when servicing 

auger belt, run the engine until the fuel tank is empty, as instructed in 
Replacing Belts. 

1. 

Tip the snow thrower up and forward so that it rests on the auger housing.

2. 

Remove the spring that connects the transmission to a bolt on the engine 
frame. See Figure 20.

NOTE: 

It may be easier to first remove the flange lock nut, then use needle-

nosed pliers to firmly grip spring and remove from bolt.

Belt Keeper

Flange 
Lock Nut

Drive Belt

Spring

Drive Pulley

Figure 20

3. 

Pivot the transmission forward to release pressure on the drive belt. Remove 
belt from transmission pulley.

4. 

Remove the drive belt from around the engine pulley, and away from the 
unit.

5. 

Place the new drive belt into the groove on the engine pulley. See Figure 19.

6. 

Tilt the transmission forward and position the drive belt onto the 
transmission pulley.

7. 

Reconnect the spring to the bolt on the engine frame and secure the 
transmission. Reinstall the flange lock nut.

8. 

Install new auger belt.

9. 

Reassemble the belt cover on the snow thrower.

10.  Reassemble the belt keeper to the housing.

Summary of Contents for 247.881980

























Reviews:

No comments

Brands by name

Popular brands

Load more brands